Dang now I gotta get me one, Thanks.. I am still waiting on my 3 MiHecs
Dang now I gotta get me one, Thanks.. I am still waiting on my 3 MiHecs
Ben:
Great thread on the 35-200 conversion, and I can't believe I missed that one when it first came out. I have the NOE 3589 with a HP cavity, and Rick converted a Lyman 358318 for me. I haven't had much luck with the 3589 in the Whelen (16 twist Remington) but it has been great in the 356 Winchester. I plan to test the 358318 in the Whelen this fall.
I'll definitely send pictures when the moulds get back - Rick has always exceeded expectations in every way!
Tony
Thanks Tony
Yes, keep me up to the minute with some photos of your mold, we'd all like to see them.
Best,
Ben
Thanks to you Ben I just ordered a 2 cavity NOE mold just like yours.
See ......you're helping out the economy. That's great !
Ben
Based on my experience with HPs in 311041, 311299 and 323471 Pin D in that 311284 cast of WW/lead at 50/50 will give excellent results on deer in your target velocity range. Expansion will be better tha straight WWs with the expansion petals not shearing off as easily. Pin B is a little too long as I've found a HP that is only about 2/3 the length of the nose works best. Both will certainly kill a deer though. Just my thoughts.
Larry Gibson
Larry ,
I certainly respect your opinion.
I think you are right on target with your views and comments !
Ben
Last edited by Ben; 08-25-2010 at 10:06 PM.
Ben, I just got some range time with this bullet out of my Krag today. A caseful of WC860 produced an avg velocity of 1807fps and a SD of 21. I believe I used Rem 9 1/2M and will try to get the SD down by using WLRM primer next go round. Accuracy was nearly on par with some Nosler 168s I had loaded to 2000fps! I was fireforming 303 Brit brass and was quite surprised by the accuracy. Judging by the reaction of a 10", 1/2" thick steel plate, if you hit a deer with any of your bullets, it's going down! If the chain holding the steel plate was a bit longer I do believe it would have wrapped over the crossbar above. This was at 100yds. Used to hitting the plates with 123gr bullets at 2400fps and seeing them barely move, I was very impressed. Whop! Forgot to mention I was using Blammer's checks, Hornady's shaved and the bullets weren't too accurate after that.
Last edited by madsenshooter; 08-25-2010 at 05:52 PM.
madsenshooter:
Thanks for the range report. Yes, they certainly should be some hard hitting cast loads.
White tail deer beware........! This is with HP pin " B ", Lee Nose 1st sizer, sized to .310 " with Ameri-max .014 thickness g/c :
Ben
Last edited by Ben; 08-25-2010 at 10:08 PM.
love those hollow-points. keep them coming.
hollow-point .......... member in south australia ...............THE MAN WHO NEVER MADE A MISTAKE NEVER MADE ANYTHING!!!! mature age is a privilige granted to but few!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |