Feeler: Re-run of NOE .359-190 RF

[Beerd]

I'm looking for others who missed out on this mould the first time around.

We need 5 confirmed orders to make this a Small Group Buy.

As part time mould makers the boys at Night Owl are booked up thru June, so depending on when the order went in this mould would come out around July.

Anyone interested?

[359-190Gr GC RF
The Ranch Dog TLC 359-190 RF bullet was designed for Marlin rifles chambered in 35 Rem. & 356 Win.
These bullets have a standard lube groove and are designed to be furnished with or with out a gas check.
We have Michael (Ranch Dog) Reamy's consent to run this design.


Night Owl Enterprises
1645 W 150 N
Provo, UT 84601
Manufacturer of premium bullet moulds.

We specialize in group buys of any type.
We offering the following:

Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

RG-2 hollow point mould $96.00 Ea.
RG-4 hollow point mould $126.00 Ea.

Plus Shipping/Handling.
Prices are subject to change at any time.
We can cut gas checked and non gas checked cavities in the same mould if the bullet is designed for it.
Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould as well as a sample of Bull Plate sprue plate lube.


We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.

[Beerd]

I will try to keep this list current

1. Beerd ..................... RG4 - 2GC, 2plain
2. Tony65X55 ............. 5 cavity GC w/ 1 HP
3. lmcollins ................. 4 cavity GC
4. 358wcf ................... 4 cavity GC w/ 1 HP
5. sundog ................... 4 cavity
6. Little Doc ................ 5 cavity - 3GC, 2plain
7. Landric ................... 2 cavity PB
8. GLL ........................ RG2 - 1GC, 1PB
9. 475/480 .................. 5 cavity GC
10. Greg ..................... RG2 GC
11. jbgoodstok ............. 2 cavity GC

5 February - Current buyers list on Page 2

[Tony65x55]

Oh ya! Beerd, I am so in. I'll take a five cavity GC with one cavity hollow pointed. The Ranch Dog designs are the best and Al Nelson's renderings of them are superb. My .358's and my .35 thank you for this, I missed out on the last one.

Do you need a PM sent to you?

Tony

[lmcollins]

I am in for a four cavity. I've been crying ever since I missed the firsr GB.

[358wcf]

Heck Yes!
I'm through missing these group buys on 35cal molds!
Put me down for a 4 cavity with 1HP- all gas-checked, please!
And thanks!!!
Notify me when payment is due, please-

358wcf

[GSaltzman]

Anyone use this boolit in a 35 remington contender?

[lmcollins]

Make my four cavity all four gas check.

[sundog]

Okay, I'll be #5 with a 4-cav. Let me know about financing...

[Little Doc]

i would like a five cavity with three gc and two plain base. tell me how to pay you.
little doc

[miestro_jerry]

I have used this bullet in my contenders, they work well, but back the load off a little.

Question, has any one RD about this, he did a lot of R&D for these bullets, he should get some credit for his work.

Jerry

[SwedeNelson]

miestro jerry

I agree with you.
Michael Reamy did a great job on the
Ranch Dog line of bullets.
And I thank him very much for letting
us run them in a standard lube groove
variation.

Swede Nelson

[Tony65x55]

Jerry, it says in the first post these are being run with Michael's consent. Michael (Ranch Dog) did a masterful job designing these fabulous boolits and Al's NOE executes Michael's designs far better than Lee ever did. Anyone who has never seen a Ranch Dog boolit meet deer hide is missing an experience. Thanks for bringing this up. Michael Reamy is only started to be recognized as a great bullet designer

Tony

[Beerd]

PM sent to those on the current buyers list.
..

[SwedeNelson]

OK this one will go on the production schedule.

List of orders.
1. Beerd RG4 2GC 2PB
2. Tony65X55 5 cavity GC w/HP
3. lmcollins 4 cavity GC
4. 358wcf 4 cavity GC w/HP
5. sundog 4 cavity
6. Little Doc 5 cavity 3GC 2PB
7.
8.
9.
10.

Will take orders up to the month before
it runs (June) and request money then.
If we can move the schedule up we will.

Thanks
Swede Nelson

[Landric]

Put me down for a 2 cavity 2PB.

[GLL]

I will take an RG-2 ( 1 GC + 1PB ) plus a blank pin set.

Jerry

[Tony65x55]

Great news Al and Beerd, THANK YOU!!!

[475/480]

1- 5 cavity -GC


Sean

[Greg]

Al-

Put me down for a RG2 Hollow Point with Gas Checks, please

what top punch will this need ?

[jbgoodstok]

Can I still get in on this - if I can I want a double cavity gc mold - thanks - jb