Lathesmith's Star dies

[wildphilhickup]

Hi Lathesmith.
I would like to order a size die, PM sent.

[Ithaca Gunner]

Cris, I'll be placing an order shortly for Star .430 die, punch, and nut-.452 die, punch, nut-.378 die, punch, and nut. Please advise of a total and I'll get a check out.

[rca]

how much for star .355 flat end punch and lock nut ?

[mack1]

Need a .427 sizer and flat punch, standard lube holes ok using for a big boolet so will plug the extras.

[mack1]

Well I installed the .427 sizer today and exactly what I asked for was the result, a .427 boolit for my 44WCF. Thanks for the very fine machine work I wouldn't think of looking anywhere else for a Star sizer die.

[Sniper Doc]

PM just forwarded with order info for 3 dies. Thanks!

[denul]

.401 star sizing die, top punch, and nut for punch needed; PM sent , Thanks

[mack1]

.401 Star sizing die and punch needed also. PM sent, thanks

[Shotgunnsteve]

I am interested in the purchase of some dies. I would like .401m, and .357 to start. Maybe a .309? My old machine says Star Machine Works, San Die Go Calif. Pat No 2,031,850. Steve @ Shotgunnsteve@gmail.com or 541 840 3646. Pretty much any time. Thank You Sir.

[K-Rod]

Chris - sent you a PM for a sizing die.
Thanks

[GP100man]

Chris do you build the die removal kit , I`ve moved my reloading benches & misplaced dies & kit .

Wanna purchase the removal kit first as the one I had was sorta rigged from washers , then maybe the rest will show up !!

GP100man

As I have gleaned yet more info from this forum I found to remove the die is to warm the sizer then push it out.

Works wonderfully!

Found my dies & removal kit with original handle , funny I don`t remember having the handle , CRS is becoming my friend as I get older!!!

GP

[jimr@martineer.net]

Lathesmith

Please provide quote for two Star/Magma bullet resizing dies. 1ea. for 38 Cal (.357"), and 1ea. for 44 Cal (.429").
Also, do you accept credit card transactions?

My Cell #(580) 695-4229
email: jimr@martineer.net

Thanks,

Jim Roach

[jimr@martineer.net]

Hi Lathesmith, It would be great if I had a phone number to call and discuss what I need and get your answers> I could then place my order. The forum/text business takes too long. I provided my email address and cell number. Please do the same. Thanks, Jim

[Cletis Richards]

Are you still actively making dies for the star?

[chas8180]

Same here, I’m in need of: .401, .430 and.452. I tried to message you as well but it doesn’t look like they went through on my end.

[Hometek]

Received .430 die and punch set. Ordered 2/28 received 3/18. Very pleased. Thanks.

[K1morgan]

I am interested in a .356 die for 9mm for my Magma sizer. How do I get in touch with lathesmith. I am not that knowledgeable about searching the internet. Thanks

[robertbank]

I am interested in a .356 die for 9mm for my Magma sizer. How do I get in touch with lathesmith. I am not that knowledgeable about searching the internet. Thanks

PM sent with email addy.

Take Care

Bob

[earlmck]

I got the three dies from you a couple weeks ago with the 5 close-spaced rows of lube holes but have only used the .401 so far. But I have to tell potential customers that your ability to do a custom lube hole spacing is wonderful for us fellows who are lubing Ranch Dog style bullets or others with the small/close lube grooves. These will make my bullet lubing go much better now that I can do them in one pass rather than be forced to do a second pass with different punch adjustment. Thanks Chris!

[Snt220]

How do I get in touch with lathesmith? In desperately need some sizing dies.