300 BO Cast HEAVY ???

[cwlongshot]

I have to leave 309–230 mold it's been OK since I removed the boat tail/gas check shank. A friend bought an arsenal, 250 grain bullet. It's also shot really well. But I'm not sure of the model and I can't seem to figure out which one it is.

I'm looking for. I'm interested in seeing what heavy bullet mold people like for this caliber. I've got a couple ideas that I like but I wanna see what's been popular and what shooting well for other people.

So can you give me suggestions for a heavy bullet 30 caliber of course, for the 300 AAC blackout

CW

[Loudenboomer]

[Iron369]

[Sig556r]

^^This^^
I believe Full Lead Taco helped designed this NLG mold

[Blkpwdrbuff]

Man, those boolits look like green beans

[Iron369]

^^This^^
I believe Full Lead Taco helped designed this NLG mold

He did. I talked with him about it.

[Iron369]

Man, those boolits look like green beans

I have lots of colors.

[sukivel]

I like this one alot.


Sent from my iPhone using Tapatalk

[johnsonian09]

I also use the Full lead taco mold for my 300 blackout subs


Sent from my iPhone using Tapatalk

[cwlongshot]

I found these last night... ACCURATE PREFERRED as I can change dims to suite. But NOE cheaper...

NOE has fixed .299 nose and 4 cav is under 100$ with rebate.

Accurate for almost same 4 cav is 150$ but I can adjust dia of body and nose to better .297 for PC .0015/.002 (per side)

NOE: HTC 310-247

Accurate: 311-245ez

[barrabruce]

https://www.castbulletengineering.co.../309-225gc.png
This does pretty well and has a fp

[Finster101]

https://castboolits.gunloads.com/sho...+.300+Blackout

This was an old group buy, but I believe he stocks it now. I have the solid version and it has run well in three ARs. The hollow point version should as well if you have a need for it.

[cwlongshot]

I am going with the NOE 310-247

A few private messages convince me its a small enough nose dia. Plus 1/3 cheaper and NOT AT ALL 1/3 less quality. The fact that it's IN STOCK and credits me to the 1K club $$ helps too.

CW

[popper]

PB or GC?

[cwlongshot]

PB. I powder coat & intend these for low pressure subs. No need for a GC.

CW

[Digital Dan]

I have to leave 309–230 mold it's been OK since I removed the boat tail/gas check shank. A friend bought an arsenal, 250 grain bullet. It's also shot really well. But I'm not sure of the model and I can't seem to figure out which one it is.

I'm looking for. I'm interested in seeing what heavy bullet mold people like for this caliber. I've got a couple ideas that I like but I wanna see what's been popular and what shooting well for other people.

So can you give me suggestions for a heavy bullet 30 caliber of course, for the 300 AAC blackout

CW

What use do you have in mind? Targets or hunting?

[versa-06]

Good Question!

[cwlongshot]

Target. I wont use 300 BO subs on deer might on coyotes. I should havf mold mid week.

CW

[Digital Dan]

Dunno why you want to use 'heavies' for target work. Might work, might not. I've been fiddling around with .30 caliber cast for some time now and have found nothing that shoots better on paper than a Lyman 311041.

Model 94 .30-30 @ 50 yards: https://i.imgur.com/upvGZ9n.jpg https://i.imgur.com/jmQScof.jpg

T/C Contender, .30 Sneezer: https://i.imgur.com/uPj90NK.jpg https://i.imgur.com/RFdTs4U.jpg https://i.imgur.com/sgcXAN8.jpg

It shoots fairly well with a Brooks 180 grain also. https://i.imgur.com/sXOvzlK.jpg https://i.imgur.com/rnGSDMC.jpg

Have a friend with a .300 BO that started with 240 grain cast. Switched to a 210 grain and it finally started shooting well.

[Rapier]

I developed a sub load for the 300 years ago using the Lee 230 FN that one of our casters sent me as an exchange for a good bit of 45 Colt brass. I do not normally buy anything Lee. However these bullets when PCed and sized to groove diameter, shot sub 1/2" groups at 50 with H-110. So I then bought a Lee "Cruise Missile" mould and they do work pretty well. However, I prefer the 358 MGP VS the 300 BO for hogs. This is a picture of the two, side by side.