Uncle Bubba can tighten that thing up!

[Texas by God]

For your viewing chagrin I present the latest stray dog that has appeared.
A poor 06 Winchester .22 pump that long ago ran into Bubba in Oklahoma.

I’m just getting it back in firing condition.
It locks up good and the bore(other than two burn marks) looks surprisingly ok with a tight muzzle end.

I have no idea what the brazing is for but by golly that barrel is tight now. So’s them magazine tube thingamabobs……


Sent from my iPhone using Tapatalk

[HWooldridge]

Probably a "farm repair"...

[45workhorse]

Nice patina on the brass

[Rapier]

A nice looking gun from the parking lot, but wait.......it gets worse.

Will see your Win 60 and raise you an A-5

[John Taylor]

That was a gallery gun at one time. The bore will most likely have tight spot where the weld is. I have several model 61 barrels that will work by taking about 1/8" off the chamber end.

[farmbif]

bubba got them loose bits secured real good

[Texas by God]

With Jack First’s help, I hope to upgrade it to Working Wallhanger Conversation Starter.
It needs a mag tube and firing pin retainer to see what’s what. A .24 caliber brush went thru the bore steady with no rough spots.
Mr. Taylor,
What features distinguish it as a Gallery gun?
The rifle buttstock?
It’s S-L-LR according to the barrel stamp.
It does give off that farm repair vibe- but it needs a bit of baling wire(Unifix) on it to complete the experience


Sent from my iPhone using Tapatalk
BTW, that A5 is still good to go, ain’t it?

[Rockingkj]

Thinking replacing the black tape at the wrist with bailing wire might be just the ticket. ��
Seriously looks like a fun one to plink with.

[405grain]

Pump action rifles just have a unique charm to them. They're so light, fast, and fun to shoot. Even as beat up as that Winchester is, a jackrabbit would be proud to get dusted off by it.

[beemer]

I have seen a lot of very poor repairs on old guns around here. Wired up stocks, nails improvised for firing pins, rubber bands to reinforce weak springs and double barrels spot brazed together. Some look to never seen oil since new and a few were dangerous on the back end too. Most were a product of depression era repairs. There was no money, if you had any it bought food and clothes. They still needed a gun and did the best they could.

[Hannibal]

My God. Is it really getting to the point where things like these are the only 'project guns' to be found?

[Texas by God]

My God. Is it really getting to the point where things like these are the only 'project guns' to be found?

This one found me. If I wasn’t a close friend to the family I’d say NOPE.
I’ve a small pile of bolt action quality project guns. Lord willing, I’ll get to them too.


Sent from my iPhone using Tapatalk

[Hannibal]

I've done a few of those too. Hopefully no more will find me. I just have a hard time turning them loose after spending that much time with them.

[Winger Ed.]

Some gallery guns had the S,L,LR option for chambering, but they'd be sort of rare.
The pumps Winchester marketed to the carnival shooting galleries were usually chambered only for .22 shorts and sold in bulk.
And had 'WINCHESTER' very deeply stamped on the left side of the receiver to get some free advertising.

Being S,L,LR, it was probably bought by someone shopping at the local small town hardware store or in the Sear's catalog.
Guns sold in the city usually don't have near the 'mileage' as country guns.

Put some fresh electrical tape on the grip, so it doesn't look tacky,,,, and it should be good to go.

[stubshaft]

Good ole Bubba...Taught him evrything he knows

[waksupi]

On the bright side, no worries about making it a truck gun!

[John Taylor]

With Jack First’s help, I hope to upgrade it to Working Wallhanger Conversation Starter.
It needs a mag tube and firing pin retainer to see what’s what. A .24 caliber brush went thru the bore steady with no rough spots.
Mr. Taylor,
What features distinguish it as a Gallery gun?
The rifle buttstock?
It’s S-L-LR according to the barrel stamp.
It does give off that farm repair vibe- but it needs a bit of baling wire(Unifix) on it to complete the experience


Sent from my iPhone using Tapatalk
BTW, that A5 is still good to go, ain’t it?

The mag tube is cut for a speed loader. This was common for gallery guns so they could be loaded fast. I don't think I have seen an 06 marked on the side with Winchester but the model 62 and 61 used the Winchester marking on the side of the receiver on some , usually with some red in the letters. Also some of the gallery guns had a way to attach a chain to the barrel, a small metal band around the barrel.

[eastbank]

a friend has his greatgrands winchester 1897 pump 12 ga that good loose from firing or screwing up the take down parts, anyway it has three small tac welds at the take down joints. it shoots ok, but its not a takedown any more.

[Gtek]

File in, polish, a little scrolling and your initials. Farm Bling?

[Rapier]

If you really want to invest the time in this old gun, looks to me like you could cut the weld off without disturbing the barrel too much and heat the brass/bronze braze and brush it off with a wire brush when runny. If you can get the stock off, it can be duplicated in straight grain American Black Walnut, which was a Win utility stock wood for many decades.
If you can find Bill from Wind River Rifle Co, they have copies of the old Win lettering. They were in Ft Walton Beach, FL a while, and moved. They also make old spec barrels and have a duplicator lathe, plus rifling machines.
I have some straight grain that I carried in supply for Bill.