Titan ReloadingRotoMetals2Lee PrecisionWideners
MidSouth Shooters Supply

Results 1 to 12 of 12

Thread: Resizing 357 Maximum for 357 magnum shot loads.

  1. #1
    Boolit Master
    Join Date
    Mar 2008
    Location
    UTAH!
    Posts
    672

    Resizing 357 Maximum for 357 magnum shot loads.

    What can be used to resize the mouths of 357 Max brass so they will fit the 357 magnum cylinder? A 9mm Lee Factory crimp die? Lee bullet sizing die, .356? A 9mm size die?
    IT IS A FINE AND PLEASANT MADNESS !

  2. #2
    Boolit Master

    Join Date
    Mar 2011
    Location
    oklahoma
    Posts
    2,221
    i don't exactly remember what I used. I am sure I posted it in my thread from a year or two ago, but I think it may have been a Lee or NOE bullet sizing die around .356 to .360"

  3. #3

  4. #4
    Boolit Buddy
    Join Date
    May 2020
    Posts
    161
    MIght have used a 38 special crimp die or 9mm crimp die

  5. #5
    Boolit Master

    jcren's Avatar
    Join Date
    Nov 2014
    Location
    South, Central Ok
    Posts
    2,146
    Not sure on 357 mag, but I used a 327 mag sizing die to "shoulder" some cut 223 brass to make 380 acp shotshells that were the same oal as a conventional load. Worked better than expected.
    "In God we trust, in all others, check the manual!"

  6. #6
    Boolit Master

    Join Date
    Mar 2011
    Location
    oklahoma
    Posts
    2,221
    I did use a 327/32 seater die (0.330") to create the "neck" on the maximum brass.

    For some reason, probably because the case isn't supported, the "neck" did not form concentric to the body with the 0.356 die. It needed a smaller constriction in order to fit in the chamber.

  7. #7
    Boolit Master Rapier's Avatar
    Join Date
    Sep 2020
    Location
    NW Florida
    Posts
    606
    Just trim to 357 mag trim to length and reload using 357 Mag dies. They are the same case just a bit longer on the Super Mag (Max).
    “There is a remedy for all things, save death.“
    Cervantes

    “Never give up, never quit.”
    Robert Rogers
    Roger’s Rangers

    There are three kinds of men. The one that learns by reading. The few who learn by observation. The rest of them have to pee on the electric fence for themselves.
    Will Rogers

  8. #8
    Boolit Master

    Join Date
    Mar 2011
    Location
    oklahoma
    Posts
    2,221
    Quote Originally Posted by Rapier View Post
    Just trim to 357 mag trim to length and reload using 357 Mag dies. They are the same case just a bit longer on the Super Mag (Max).
    The OP is attempting to load shotshells that are the full chamber length, not just loading 357 magnum cartridges.

  9. #9
    Boolit Master trapper9260's Avatar
    Join Date
    Feb 2010
    Location
    Iowa
    Posts
    3,151
    Quote Originally Posted by BK7saum View Post
    The OP is attempting to load shotshells that are the full chamber length, not just loading 357 magnum cartridges.
    The way it sounds then , just have the case full length of the cylinder and then load . Might need some adjustments for how it sounds. I am not sure I have not done it yet. But give me a idea to work on this winter.
    Life Member of NRA,NTA,DAV ,ITA. Also member of FTA,CBA

  10. #10
    Boolit Master
    Join Date
    Aug 2014
    Location
    South Central PA
    Posts
    751
    Back when I looked into doing this, there was a die to star crimp "blanks". That was the route I was going to go.

  11. #11
    Boolit Master
    Join Date
    Jun 2012
    Posts
    696
    Star crimp ruins cases

  12. #12
    Boolit Buddy
    Join Date
    May 2016
    Location
    Near the Keg
    Posts
    228
    I don't know your circumstance, but it may be worth going in another direction for a dedicated "Snake/Rat Gun." The Bond Arms "Roughneck" Derringer in .357 can be had for as low as $250. Ream it out with a 357 Max reamer and you have a pretty lightweight little snake gun that is easy to reload for and does not wreck the brass. I did the same to a Bond Arms 45 Long Colt and had it cut with a 460 S&W reamer. Still working up shot loads for it, but it holds way more #11 shot than a .410 shell does. Who knew that Harvester Muzzleloader 45cal Hi-pressure Sabots make excellent shot cups?

    The bonus is that the barrels are relatively cheap and you can easily convert it back.
    Alcohol Inventory Reduction Specialist (Journeyman Level)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check