I am going to try and find a mold for .358 dia. bullets to shoot in a 35rem tube magazine.
Either a flat point or a round nose.
What do you recommend or use. do you load and what about gas checks?
Thanks Dave
I am going to try and find a mold for .358 dia. bullets to shoot in a 35rem tube magazine.
Either a flat point or a round nose.
What do you recommend or use. do you load and what about gas checks?
Thanks Dave
One thing... If that is a regular "twisted tube" Remington.. no amount of point is ever a problem, because the nose cannot sit against the primer of the one in front anyway.
I bring this up, because the 150 condom, Remington PSP, really is one of the best in my 357 Herrett, and the 35 Remingtons around here.
But, having heard really good things about the RCBS 200 FPGC, I will be trying that .. As You Should.
Pistol Bullets don't feed too good in my personal 35Rem, maybe because it is a bolt action.
Good Luck
RCBS 35-200-FN and H4895.
Larry Gibson
“Deficient observation is merely a form of ignorance and responsible for the many morbid notions and foolish ideas prevailing.”
― Nikola Tesla
thanks should have listed the rifle.
Its a Marlin 336, tube magazine?
If I keep velocities under 1800 feet/ sec. I should not need a gas check?
Thanks
Last edited by DCB; 04-16-2021 at 10:11 AM.
This is the gold standard bullet for the 35 Remington. I doubt you can get anywhere near 1,800 fps without a gas check. Get the gas check bullet and use them if nothing else but for insurance for your accuracy. 1,800 fps may be about the top velocity you can expect with a gas check and the proper powder, which Larry has made an excellent suggestion. One thing of importance....is it an older Marlin with Ballard rifling? or is it a later Marlin with Microgroove rifling?
Good Luck,
Rick
That is the One .. I should Know very soon!!!
IDK about that high!! I can't do it...
Brewer 12345, is sending me some Accurate 36-180L, plain base 180's to try, and I do Not anticipate going over about 1400 fps.. seems like a good place for me to be with such a boolit, providing it Feeds, which I really think it will..
Edit; Looking over the Accurate offerings, I am going to try to source a 140 to 160 grain Boolit. Plain Based. That will do double duty as a 35 Rem. "Fun Load", as well as a load for my 357 Mag(s), loaded in 38 Spl Brass.... Wish me luck!!!!
Last edited by racepres; 04-16-2021 at 10:49 AM.
This is a sweet combo for the 35 Rem Marlins. I have a '52 with Ballard rifling and my son's is a micro groove. Best groups ave been at or just under the factory load level of 1900-2000fps. If a micro groove you will need a large enough diameter to tightly fill the grooves and a GC at 1800. A bit harder alloy or HT/water dropped helps too. Never tried a flatbase or unchecked boolit in the Ballard rifled 336.
Thanks for all the info and insight.
Molds are pretty hard to get.
Thanks Larry Ill look for a rcbs 200gr. GC.
I really really like Lee's copy of that RCBS flat point 205 grain boolit. And they make it in the 6-cavity. That's what I've been running for several flavors of 35 Remington: Remington, Savage, and Marlin. Yep -- I've got a Savage 99 that was converted to 35 Rem.
The RCBS 35-200-FN over 31.0 grains of Alliant RX7 makes 1,932 FPS average from my Marlin. 5 shot groups average right around an inch at 50 yards with an elbows rest and my tired old eyes.
”We know they are lying, they know they are lying, they know we know they are lying, we know they know we know they are lying, yet they are still lying.” –Aleksandr Isayevich Solzhenitsyn
My Straight Shooters thread:
http://castboolits.gunloads.com/show...raight-shooter
The Pewter Pictures and Hallmarks thread:
http://castboolits.gunloads.com/show...-and-hallmarks
Although I haven't looked, I'm sure Tom at Accuratemolds.com has the RCBS 35-200 cataloged. I think you would want the diameter such that you could size to .360", at least I have to for my 35 Remington Marlins. Better to be a bit big than even a little too small. If you order from Tom you can usually have your mold, a most excellent product, inside of a couple of weeks. I don't expect there is a shortage at Tom's place.
Good Luck,
Rick
I like Lee’s 35-200 FP GC and 12 grains unique. I believe about 1500 FPS out of my waffle top Marlin 336. Very nice combination and very accurate. Easy on shoulder as well.
Rickintn, They have a ton of molds. thanks for the comment. now i will have to figure out which one I want.
MP 640-160 Cramer these have the penta HP .360 PCed Plain base over Unique/Red Dot
Last edited by NyFirefighter357; 04-17-2021 at 07:30 AM.
Look like some nice bullets what is the bullet weight?
Have you shot any deer with that bullet and how did it perform What Velocity do you get.
Thanks Dave
I use the Ranch Dog bullet that was designed for the Marlin, the noe 359-190-rf, about 188gr, wcww, 35gr Benchmark and Fed LR primer. This bullet and load works well in my Marlin and a Model 14 Remington.
Thanks, the ranch dog bullets, are they tumble lubed or powder coated.
what powder and size groups are you getting. Does your Marlin have micro grove rifling?
Dave
The Ranch Dog bullets are designed for tumble lubing, but I just lube it in a Lyman at .359" and cast from air-cooled wheel weights. Load with 35-36 gr IMR 3031 and a standard rifle primer. My Marlin was made in the early 80's and has the micro-grooves. These targets are fairly typical of the accuracy I get with this load.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |