Does anyone have the OEM part name and number for the Bullet Ejector cylinder on the Magma Bullet Master? Think its BM440 under the magma manual.
I have emailed Magma a few times but have not had a response. I guess they are snowed under with work.
Does anyone have the OEM part name and number for the Bullet Ejector cylinder on the Magma Bullet Master? Think its BM440 under the magma manual.
I have emailed Magma a few times but have not had a response. I guess they are snowed under with work.
Electric or air solenoid?
"EXPERT= Ex is a has been, spurt is a drip under pressure" Unknown
Sent from my iPhone using Tapatalk
John 15:13
Greater love hath no man than this, that a man lay down his life for his friends.
Thank you too, i have searched their site, yet can't find it.... I'm not sure what they call them so i can even look for an alternative in another brand.
Ok, on further inspection, i seem to have found an archived post from the forum giving the following alternative:
https://www.smcpneumatics.com/NCMB075-0050S.html
I assumed the cylinder had a reciprocating valve, so you just apply air and it automatically keeps striking, not just a single tap.
I will let you know what I find, I found an alternative for around 20 bucks so cheap enough to throw away if it doesn't work. Will keep you posted.
PS - this is for the cylinder to eject the bullets.
Awesome, looking forward to hearing how it goes.
If you're talking about the piston for knocking the sprue loose from the sprue cutter, I've been using this one:
https://www.zoro.com/speedaire-1-116...j6/i/G1990152/
This is the piston that strikes the sprue cutter to knock the sprue loose just before the mold opens all the way to drop the bullets. It mounts to the outside of the machine, on the left side as you face the machine.
My machine is an old Mark 6, and the aluminum hammer head on the end of the piston was pretty beat up and flattened, so I turned a new one out of brass. It gives it a little more impact, but still doesn't beat up the sprue cutters, and it's been lasting pretty well.
Hope this helps.
Fred
After a shooting spree, they always want to take the guns away from the people who didn't do it. - William S. Burroughs.
Thanks for the link Fred. No matter the material you use, it will eventually mushroom, but with a lathe, you just cut a new one
you need a Repeat Cycle timer relay looked at one of our machines on a mk 6 the pour
time is what fires the cylinders you would need to set it up
for your fastest pour time
When input voltage is applied, the relay turns on for the on-cycle time. Then the relay turns off for the off-cycle time. This process repeats until the input voltage is removed.
like this one you can control both the on and off to .1 sec https://www.amazon.com/DH48S-S-repea...strial&sr=1-58
forgot you will need to add a solenoid valve at the cylinder and wire it to the timer circut for the sprue knocker
mike
Last edited by m37; 04-10-2021 at 09:01 AM.
Easier way of doing it. I had tappers setup on my master caster, my brother added something to the code to make the cylinder cycle just like that timer does. It did the job, but beat the absolute snot out of the brass ends, but that was to be expected with each cycle it would strike 5 or so times
on the bullet masters mk6 is the newest we have they are all relays and wires
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |