ACTIVE - MiHec 8mm Sil Rerun 2 & 4 Cavity HP / 6 & 8 Cavity Solid

[Wasalmonslayer]

Miha is giving the green light on this mold for a rerun.

Thank you to the designer and all past participants in the last buy!

MiHec 8mm Sil brass
This is a sign-up thread for an old GB & BRP mold design........ specifically a heavier cast boolit for the 8mm caliber rifles. This boolit is a gas check design. It casts out slightly above 0.326" and sizes easily to 0.324". Ready to load weight is about 200 gr. dependent on your alloy. It has fit in everything we've tried it in. To date the best load has gotten sub 1 MOA at 100 yds....... due to lack of a good scoped rifle.

The costs will be as follows-

- 2 Cavity HP all pins included 95 Euro's (80,75 with discount)
- 4 Cavity HP all pins included 135 Euro's (114,75 with discount)
- 6 Cavity solid Brass (80,75 with discount)
- 8 Cavity Aluminum (80,75 with discount)

Prices and options are to be confirmed by MiHec they may change!

Please give your disguised e-mail address and the number and type of molds you want.

As always these buys can take time please be patient and give grace. Getting upset will not make it go any faster!

The discussion thread is here: http://castboolits.gunloads.com/show...27#post1603627

[Wasalmonslayer]

Sign up List

Solid Molds-

1) kawacharles1973 at gmail dot com - 6 Cavity Brass
2) Shawn smc at hot mail dot com - 8 Cavity Aluminum
3) Jay Aich at Hammer Bek dot com - 8 Cavity Aluminum
4) lattanzizxc att gmail dot com - 6 Cavity brass
5) zipporaider1968 at yahoo dot com - 6 Cavity Brass
6) r dot nittritz at telus dot net - 6 Cavity Brass
7) drctml AT yahOO dot COM - 6 Cavity Brass
8) dcasad(at)hotmail(dot)com - 6 Cavity Brass with handles.
9) Ed at trilogy-health dot com - 6 Cavity Brass
10) aveni1955 at yahoo dot com - 6 Cavity Brass
11)
11)
HP Molds

1) scottturknett at hotmail dot com - 4 Cavity HP
2)
3) lattanzizxc at gmail dot com - 2 Cavity HP
4) kc5vtk at comcast dot net - 4 Cavity HP
5) m_worlund at yahoodotcom - 2 Cavity HP
6) ckulyk at telus dot net - 4 Cavity HP
7) Jay Aich at Hammer Bek dot com - 4 Cavity HP
8) zacalldredge at gmail dot com - 2 Cavity HP
9) adamjsmith80 at gmail dot com - 4 Cavity HP
10) Dan esc h n er At Gmail dot com - 4 Cavity HP
11) miamileo3 at yahoo dot com - 2 Cav HP
12) lotar95 at gmail dot com - 4 Cav HP
13) drccac at zoomon dott net - 2 Cav HP
14) Peeeeeeeebeeeeeeslingeratprotonmail dot com - 4 Cav HP
15)
16)
17)
18)
19)

[bns454]

Is there a drawing somewhere with sizes showing the nose diameters/profile ?

[Wasalmonslayer]

Is there a drawing somewhere with sizes showing the nose diameters/profile ?

I just attached a couple of photo's

[Uncle Dave]

Your opinion please - would this be a good mold for both 8mm (Mauser) and 32 WS (94 Win) with the appropriate sizing of course? The picture of the flat nose or hollow point MIGHT make it safe for tube feed rifles. Any actual experience anyone?
Thanks
Uncle Dave

[bns454]

I just attached a couple of photo's

I worded that wrong,Sorry.Can we know the approximate diameters as cast after that front drive band.

[Kawacharles]

I'm in: (1) 6 Cavity solid Brass mold.

kawacharles1973 at gmail dot com

[Wasalmonslayer]

Is there a drawing somewhere with sizes showing the nose diameters/profile ?

I messaged Miha to see if we could get a few specs.

[bns454]

Thank You !

[Wasalmonslayer]

Your opinion please - would this be a good mold for both 8mm (Mauser) and 32 WS (94 Win) with the appropriate sizing of course? The picture of the flat nose or hollow point MIGHT make it safe for tube feed rifles. Any actual experience anyone?
Thanks
Uncle Dave

Good morning
I have no personal experience with either of them but maybe someone else will chime in to help out.
I do know it may be a little sketchy in the win 94 tube just for reasons with the bullet being pushed back in the case.
You would have to do a decent crimp to get it to hold.

[shawnsmc]

I'm in for an 8 cavity. Shawn smc at hot mail dot com

[Wasalmonslayer]

I'm in for an 8 cavity. Shawn smc at hot mail dot com

Got you on the list

Thank you!

[HangFireW8]

6 Cavity solid Brass
hang fire w8 atttttt gmail dot com

[Wasalmonslayer]

6 Cavity solid Brass
hang fire w8 atttttt gmail dot com

Got you down

Thanks!

[pistol]

lattanzizxc att gmail dot com 6 cavities brass
PS New at group buys, please do inform me as to further steps to be taken... Thanks!

[5 RING]

sign me up for a - 6 Cavity solid Brass. zipporaider1968 at yahoo dot com

[AlaskaScott]

I will take a 4 cavity
scottturknett at hotmail dot com

[Wasalmonslayer]

lattanzizxc att gmail dot com 6 cavities brass
PS New at group buys, please do inform me as to further steps to be taken... Thanks!

Got you on the list.
Now we wait. Nothing else required till Miha mills them and sends you a paypal invoice.

Thank you!

[Wasalmonslayer]

sign me up for a - 6 Cavity solid Brass. zipporaider1968 at yahoo dot com

Got you fixed up

Thank you

[Wasalmonslayer]

I will take a 4 cavity
scottturknett at hotmail dot com

4 Cavity hp??
If you want a solid mold it will be a six cavity brass or 8 cavity aluminum.

Please advise