I see what is going on. This is a result of my hard drive crashing a few months back, and me losing some of my source files. I was working off an older version where the bracket was shorter by 10mm.
I think this one should do it.
APP_Brass_Insert_32SW.zip
Last edited by TylerR; 08-05-2021 at 02:04 PM.
TylerR, could I ask you for another favor? The feed_die_32_insert, could you extend the bottompart with 2.58mm as shown by the picture below, then I think it would work with Hollowbase wadcutters in .32S&W Long caliber. (leave the holes where they are, and add some length, so the steelballs fit between the bullets)
Thanks again!
Last edited by Charlie_Sweden; 08-06-2021 at 06:15 PM. Reason: added picture.
Success!
Got the parts printed and assembled but the plate kept jamming until I realized I had the side plate in backyard. Doh!
I've since made some better looking parts using Sunllu filaments. My Ender 5 seems to do better with that filament and the settings from y'all. I did try some clear Oveture and it was a disaster, but would probably be fine with adjustments. I went back to the Sunlu, I want to build collators for two presses, a brass decapping station and some fellow handloaders.
I cannot thank y'all enough for getting me started in 3D printing.
I have an ender 3 220x220 x and y build plate and I cannot fit the main body in cura without turning it 90 degrees, in the readme it states you need at least a 210 x 210. If I increase my build plate size in my printer profile to 230x230 it fits. Its not importing at more than 100% BTW. What am I doing wrong?
Sent from my Pixel 2 using Tapatalk
I looked at a printer machine and it costs about $400. I assume another $50 for filament (not sure???) and $50 for others bits and pieces. So a total of $500. Does this sound about right?
At that cost I am leaning towards just buying:
https://www.doublealpha.biz/us/mr-bulletfeeder
For about the same $$$.
If I still had the second 1050 I could save some $$$ but I only have one reloader that needs a bullet feeder.
Don Verna
Printing is a cheap hobby. Ender 3s can be $200 and then $20 for a roll of filament. But it takes alot of work to calibrate the machine and just alot of time in general. Time is much more important than money. If all you want is a collator then forget it, but you're not thinking about the countless other stuff you can make with it.
Cant see the forest for the trees
Sent from my Pixel 2 using Tapatalk
Well that accounts for your post at 3:17 AM here in New Mexico! Nice to have a little diversity here! And nice to know your gun rights are alive and well. Hope they are not under attack like they are here......and btw, I love the originality found in Swedish Jet Fighters!
I have a few grams of Swedish blood in my veins.....and Danish too.....back a few generations..... (along with English and Swiss) My sir-name came across the English channel with William the Conqueror's Army.
Last edited by GWS; 08-13-2021 at 02:43 PM.
Started a 2d feeder to match my lee setups .. Also trying the app parts in resin . They look really good
Last edited by Vorga; 08-14-2021 at 01:35 PM.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |