What did you do in the reloading room today?

[Brassmonkey]

Loaded 80ish rounds of 9mm Nickle case 5 grains of "pistol powder" 124gr jword mixed HS mostly speer and fc, then fired them. had three cases split one at the rim the other 2 in the middle, just tiny separations. had one failure to feed from each mag, but a snap back on the slide and it went. should have pulled the round to check for OAL but oops.

also had a .380 case slip through, two of them but I caught the one. now I dun wasted a primer cause I don't have a .380

something wrong with picture uploading? tried a few times and it kept failing.

[smithnframe]

Reloaded 220 rounds of 348 Winchester for my Siamese Mauser!

[Remiel]

Pulled apart 1 of 2 lee pro 1000 presses I found on marketplace to clean and replace worn/broken parts

Sent from my SM-G970U using Tapatalk

[onelight]

Loaded 451 45acp with 185 gn RN on 6.4 grains of BE-86 with the Lee ABLP took about an hour and 10 min.

[whisler]

Sorted a bunch of brass a friend gave me.

[flyingmonkey35]

Finaly gomy in line mounts setup

Sent from my SM-G960U using Tapatalk

[Soundguy]

Made up a batch of Felix lube. Stuff looks good. I love the consistency. Can't wait to try it. I should have a rifle mold coming in tomorrow..8mm mauser.. Might use it then.

[MOA]

Added a 300 Savage set of dies to the inventory to get my SIL setup to load with.

[whisler]

De-priming some free brass a friend gave me. Its good to have friends.

[MOA]

Just got in another Savage set of dies for the Savage 250-3000.








Just got to love the "Green box".

[onelight]

Cleaned 350 44 special cases and 50 44 mag primed a hundred then my youngest grandson 7 year old and I loaded 50 44 specials on the Lee LCT with red dot and some 200 grain RNFP bullets , he did about 25 with me watching and then I did 25 he is still a bit light for resizing but he got through 25 doing all but priming

[Soundguy]

Cast 250 175gr .324's

Started lubing and glass checking them. Think I went a hair too hard.. Quite tough sizing..

[sigep1764]

Polished and cleared the flash holes of 400 223 tonight. Gonna load them tmro with my second batch of powder coated boolits.

[1I-Jack]

"Delivered" three of these to my shop. 250# of range scrap. We cleaned out the bullet trap at the local indoor range and the scrap is left in 55 gal drums for members to take as needed.

[The Dar]

"Delivered" three of these to my shop. 250# of range scrap. We cleaned out the bullet trap at the local indoor range and the scrap is left in 55 gal drums for members to take as needed.

Go back and get the rest, fill your "need".

[44Blam]

Cast couple hundred 225 tacos and about 500 190 grain 40s...

Those long 30 caliber boolits are very hard to cast. The short 190s are super easy...

[1I-Jack]

Go back and get the rest, fill your "need".

It'll still be there after I get this processed. (4) 55 gal drums 1/2 to 3/4 full. It's a small club, less than 150 members and not that many of them casters. This was a 2 year cleanout.

[cwlongshot]

Trimming up 250 brand new cases I reformed for a friend. (He dosnet have the set up for this reforming)

About 1/2 done trimming. Realized I had a carbide cutter I had not installed. . WOAH MUCH BETTER!!!

https://youtu.be/x_SG4i5ZU-8

CW

[Barman54]

Went Shooting my 45/70 Sharps Replica Yesterday, Moving my Loads out to 100 yds, then 200, and further.
That being said,
Woke up early had take 6 Shells apart, using some Older CCI L/R Primers, that had failed to go Bang.
Prepandemic Estate purchase, Less than 1 % fail to off.
Just using them up, one shot at a time

Pulled Bullet, sized, M Die, Verified the Charge, Reseat Bullet, Crimped, good as new

Barman54
Out

[PhatForrest]

Tweaked a friends old Lyman mag 20 pot, and made a whole pie plate full of mihec's 158 Keith swc's testing it out