I got 300 44 Mag loaded. 20g of 2400 with a Federal primer and the late #503. Only dropped one case so I'm getting better. More practice required. LOL
I got 300 44 Mag loaded. 20g of 2400 with a Federal primer and the late #503. Only dropped one case so I'm getting better. More practice required. LOL
Mal
Mal Paso means Bad Pass, just so you know.
I finished the 24 GPC brass die formed, primed, powdered and 80gr bullets loaded for fire forming, resized 20 rounds of fire formed brass and uniformed the pockets. 100 pieces of 22-250 AI brass neck sized, I used my old system with powder graphite and lead shot on half then tried imperial wax on the other half, pockets uniformed.
while resting loaded two boxes of 28 Ga shot shells.
I have three 6mms I am testing for an ATN Thor 4 thermal mounting.
“There is a remedy for all things, save death.“
Cervantes
“Never give up, never quit.”
Robert Rogers
Roger’s Rangers
There are three kinds of men. The one that learns by reading. The few who learn by observation. The rest of them have to pee on the electric fence for themselves.
Will Rogers
Not my reloading room - but headed to a buddy's house to finish up 30,000 9mm, 20,000 5.56 and 15,000 7.62 NATO. We finished casting the boolits almost 6 mo ago from a large amount of lead I procured, purchased primers for the project 3 years ago. Looking forward to watching our boys get these emptied out again!!
Sent from my Pixel 5 using Tapatalk
Cooked some 30+ Lb Piglets with a pound and a third of Tin and poured 30 casting pot ingots.
Last edited by Mal Paso; 04-25-2022 at 09:38 PM.
Mal
Mal Paso means Bad Pass, just so you know.
I finished a small batch of 44-40 and I'm starting a batch of .41 magnum. Both are loaded with 9grs of Unique. And benched the Revelation .22 rifle with old Federal Lightning ammo. A decent group for Iron sights at 40 yards but 10" high.....sights are bottomed out.....time to scope it!
Sent from my SM-A716U using Tapatalk
Bit the bullet today and Bought a 5 gallon bucket of wheel weights at the local tire shop. Looked at the top of the bucket hope in I Saw about 90% lead maybe more. They said it was an old bucket and maybe had more land than the newer buckets. And they said the last shipment of wheel weights were all zinc and steel so it won’t be long before all the lead wheel weights are gone. Haven’t weighed it but more than 100lbs. $80. Plus tax. Broke my heart paying that much.
I cast another 600 38-200 Penta Hollowpoints. Had trouble finding the groove, too cold and those boolits do not want to leave the mold. Went to 710F and had a very good run.
Loaded my last 9 free 350L cases with A11FS and a Magnum primer under a 38-200 hoping to tighten up the Extreme Spread.
Mal
Mal Paso means Bad Pass, just so you know.
Made up some more .358/9mm gas checks tonight....still haven't quite got it right as yet, but a work in progress. : :
"Think for yourselves and let others enjoy the privilege to do so too."
Finished the week long casting session. Phew.
2400 - 38/357
2500 - 9mm
2000 - 45acp
Total 6,900 castings.
160 pounds of alloy.
[SIGPIC][/SIGPIC]
I have been wanting to try ladle casting. The "Brown Santa Clause" dropped off my new Lyman Big Dipper and ladles on Friday and I spent the day messing with it today. Ran about 40lbs. of pretty .361" boolits for my 358 Winchester today. I just may be putting up the o'le bottom pour pot!!!
prepped 100 x 308 brass ,loaded 20 x 308 .must cast some boolits this week.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |