Titan ReloadingLee PrecisionWidenersInline Fabrication
Reloading EverythingRotoMetals2MidSouth Shooters SupplyRepackbox
Load Data
Page 1 of 2 12 LastLast
Results 1 to 20 of 27

Thread: IMR 700x in rifle

  1. #1
    Boolit Grand Master
    Join Date
    Feb 2006
    Location
    Kaneohe, HI
    Posts
    5,561

    Smile IMR 700x in rifle

    I've been trying out IMR700x in my SMLE and 2A.
    303- Lyman 314299 GC, un-sized, RP, no filler, Larz carnuba red lube.
    9.0gr- 50yds- 1" to 1 1/2". 100yds- 2" to 3", 7" low.
    10.0 gr- 50yds- 1" to 1 1/2". 100yds- 2" to 3", 5" low.
    308- Lee 185g sized to 309, GC, RP, no filler, Larz carnuba red lube.
    9.0gr- 50yds- 1" to 1 1/2". 100yds- 2" to 4", 6" low.
    10.0gr- 50yds- 1" to 2". 100yds- 2" to 4", 4" low.
    I'm going to try a 311 bullet in the 308.
    Seems like I could use more powder. I read somewhere the max is 14.0gr.
    Recoil was mild. Very clean burning. No primer pressure signs.
    I'm wondering if anyone else has used this powder????
    I did a search and didn't find much.
    For me, it seems to work better than Unique, Red dot and Blue dot.

  2. #2
    Boolit Grand Master
    Join Date
    Mar 2005
    Location
    Lincoln, Nebraska
    Posts
    6,063
    Truthfully, I'd be very greatly surprised if there was any difference at all in accuracy or anything else between Red Dot and 700X. I have tried these two head to head, as well as similar powders and they all do pretty much the same thing.

    I find success with lighter than standard bullets for the caliber - like, say 113 grains in the .30's - and lighter than maximum charges of 13-14 grains. Try going down in bullet weight and trying the 8-10 grain region for mild plinking loads and velocities from 1300-1600 fps. If you could get the Lee Soup Can to fit your likely oversized barrel, the range mentioned would likely produce the best accuracy of which your rifle was capable. At least with that bullet weight.

    At these charge levels you may find that standard sized bullets could use a bit more velocity, and accuracy may be sub par as you have found out. I'd go to 2400 in that case as it can drive the bullet to more useful speeds for longer ranges and better accuracy.

  3. #3
    Boolit Grand Master
    Join Date
    Feb 2006
    Location
    Kaneohe, HI
    Posts
    5,561

    Smile Tried different powders

    Thanks for the suggestions.
    I've tried Unique, 10gr to 13gr; 2400, 14gr to 17gr; Red dot, 12gr to 14gr; IMR4198, 20gr to 22gr; and Blue dot, 12gr to 16gr.
    At 50yds, all were about the same. At 100yds, they started to open up and became inconsistant. With 700x it seemed much more consistant.
    To me it feels like 700x gives a softer bang than Unique or Red dot. Kind of like Blue dot. From the burn chart, 700x is suppose to be a faster powder. Can it be fast and soft????
    I have the Lee 165 sks bullet mould. I'll try it in the 308 to see if a lighter bullet might be better. Don't have a light bullet mould for the 303. Any suggestions???? Maybe I'll try to beagel it to get it bigger.
    I'm looking for a load/bullet that would have the same point of aim at 50yds and 100yds, if possible, and group 1" to 2" at 100yds. Asking to much????
    I wish I had a cronograph.

  4. #4
    Boolit Grand Master
    Join Date
    Mar 2005
    Location
    Lincoln, Nebraska
    Posts
    6,063
    From a SMLE you're asking for a lot if you expect that kind of accuracy (1-2 inches @100), considering that most of them won't come close to that with any load, jacketed or cast.

    You have one of the moulds for the fat .30's, hopefully? Two to three inches is not bad at all for a SMLE using the issue sights at 100 yards. Most of us have learned to be content with that. 2400 has my vote for an accuracy edge over the shotgun powders at the somewhat higher velocities that you desire.

    You're not gonna get a slower cast load to hit in the same spot as a full power load at 100 yards. That's okay. Can't have it all. If your 700X proves better over several range sessions then it may be for you, but I'd still be surprised if there was any real difference between the various shotgun powders in the loadings you mention. In the .308 or .303 14 grains of any of these powders is a great plenty and accuracy may deteriorate due to a little too much of a swift kick in the rear for the lead bullet.

    From your trajectory, and assuming you're zeroed exactly at 50 yards, you're in the 1100 to 1500 fps range.

  5. #5
    Boolit Grand Master
    Join Date
    Feb 2006
    Location
    Kaneohe, HI
    Posts
    5,561

    Thanks

    Thanks for the info.
    I'll keep on playing with it.

  6. #6
    Boolit Mold Hi-Standard's Avatar
    Join Date
    Apr 2005
    Location
    Newfoundland
    Posts
    11
    Not trying to hijack here, but have any of you guys had problems using pistol powders without fillers? I've only ever used Unique without fillers in my cast rifle loads. I have 700X, 800X, AA#2, and AA#5? I reload mostly fat 30's, 7.65x53, 7.62x54R, 303 Brit. etc. I would like to avail of my other powders as well, as the plinking chews up a lot of rifle powder.
    There's a difference in scratching your **** and tearing it all to pieces!

  7. #7
    Boolit Master RU shooter's Avatar
    Join Date
    Nov 2006
    Location
    SW Pa.
    Posts
    2,928
    Any of the faster to med. speed pistol or shotgun powders I have used have been without any filler or powder wad. I have had best luck with Unique ,W231 and Bullseye 10, 7.5 and 6 grs respectively for "plinker" 100 yd loads in the 54R,7.5 Swiss, 303 and 30-06.

    Tim
    If you find yourself in a fair fight, your tactics suck!

  8. #8
    Boolit Mold Hi-Standard's Avatar
    Join Date
    Apr 2005
    Location
    Newfoundland
    Posts
    11
    Quote Originally Posted by RU shooter View Post
    Any of the faster to med. speed pistol or shotgun powders I have used have been without any filler or powder wad. I have had best luck with Unique ,W231 and Bullseye 10, 7.5 and 6 grs respectively for "plinker" 100 yd loads in the 54R,7.5 Swiss, 303 and 30-06.

    Tim
    So AA#5 being a little faster than Unique and AA#2 being a little slower then Bullseye should be ok without fillers? I guess 800X maybe a little too slow?
    There's a difference in scratching your **** and tearing it all to pieces!

  9. #9
    Boolit Grand Master


    Larry Gibson's Avatar
    Join Date
    Jul 2005
    Location
    Lake Havasu City, Arizona
    Posts
    21,303
    abunaitoo

    Are you using a GC on these bullets?

    Also, 700X is very fast burning which is ok. I suggest you use less powder instead of more. I use a lot of Bullseye with such loads as I've found it to be the best. However, 700X does well also. I'd suggest you start at 5.5 gr and work back up to 9 gr in 1/2 gr increments in both cartridges.

    Larry Gibson

  10. #10
    Boolit Grand Master
    Join Date
    Feb 2006
    Location
    Kaneohe, HI
    Posts
    5,561

    Gas checked

    I've not had to much luck without gas checks.
    Seems to be inconsistent and some leading.

  11. #11
    Boolit Mold
    Join Date
    Feb 2021
    Location
    whitehall,wi
    Posts
    14
    Quote Originally Posted by abunaitoo View Post
    I've been trying out IMR700x in my SMLE and 2A.
    303- Lyman 314299 GC, un-sized, RP, no filler, Larz carnuba red lube.
    9.0gr- 50yds- 1" to 1 1/2". 100yds- 2" to 3", 7" low.
    10.0 gr- 50yds- 1" to 1 1/2". 100yds- 2" to 3", 5" low.
    308- Lee 185g sized to 309, GC, RP, no filler, Larz carnuba red lube.
    9.0gr- 50yds- 1" to 1 1/2". 100yds- 2" to 4", 6" low.
    10.0gr- 50yds- 1" to 2". 100yds- 2" to 4", 4" low.
    I'm going to try a 311 bullet in the 308.
    Seems like I could use more powder. I read somewhere the max is 14.0gr.
    Recoil was mild. Very clean burning. No primer pressure signs.
    I'm wondering if anyone else has used this powder????
    I did a search and didn't find much.
    For me, it seems to work better than Unique, Red dot and Blue dot.
    i am here to learn with you i have alot of 700x and i just started loading 158gr sns coated for my 30-30 so a site like this is very helpful .have a great day and shoot alot.

  12. #12
    Boolit Buddy
    Join Date
    Apr 2014
    Location
    Bartlesville, Ok
    Posts
    383
    I was informed pressure curves are also part of the equation beyond burn rate, which could be the answer to your question about fast and soft. *not an informed answer, but an extrapolated guess*

  13. #13
    Boolit Buddy
    Join Date
    Oct 2020
    Posts
    312
    700x is a mouse fart powder in my view. 6-10 grs will give ~.22 LR velocities and be good plinking with light bullets. The 314299,sized and GC'd with 2400, 4198, H-322 and maybe even 3031 will make you happier at a lot higher velocities.

  14. #14
    Boolit Master
    Join Date
    Oct 2012
    Location
    Las Cruces, NM
    Posts
    4,535
    For an idea of how pistol powders do in rifles:

    http://www.gmdr.com/lever/lowveldata.htm

    I use the .30-30AI data for my .308 and it tracks pretty close.

    Do not use filler with these really light loads. I have found that accuracy changes a LOT with change in powder weight. For example, using Blue Dot and 180gn bullets in the .308, if I loaded 8.0gn the group sizes would be around 1 1/2" at 100yd (1150-1200fps). If I went to 9.0 and 10.0gn they went up to 3" and 4" (this may be due to transonic issues).

    If you want higher velocities then you go to the slower pistol powders (or faster rifle powders), like 2400, 4198, etc.

  15. #15
    Banned



    Join Date
    Nov 2009
    Location
    Kansas
    Posts
    7,068
    I like 700X and use a lot of it in all kinds of things.Almost as versatile as Unique.

  16. #16
    Boolit Master
    Join Date
    Jun 2012
    Posts
    760
    I have used plastic gas checks cut to fit friction tite in the neck under a shallowly seated bullet. Paco Kelley uses these.

  17. #17
    Boolit Master
    Join Date
    Oct 2012
    Location
    Las Cruces, NM
    Posts
    4,535
    'Back in the old days' (70's) we started using poly wads instead of gas checks in straight cases. Got the idea from bench rest cast bullet shooters. The 'common' wad back then was cork or similar material.

    It worked as intended and was an easy way to get more velocity with a plain base bullet.

  18. #18
    Boolit Master
    Join Date
    Jan 2006
    Location
    Greater Portland OR.
    Posts
    1,741
    Notes are is So.Cal. so this is from memory. 11-12 gr 700x under a fairly large cast boolit got 1/2-3/4" group at some where between 50-100 yds. Boolit was either 170 gr or 220 gr. may have had gas check. Boolits were out of Lyman/Ideal molds. Stopped loading it because I ran out of 700x. Used a lot of it for trap and skeet loads. Liked it better than Red Dot. Think it burns cleaner. This was out if a 30/06, 03a3.
    Last edited by Duckiller; 03-02-2021 at 09:01 PM. Reason: forgot to list caliber

  19. #19
    Boolit Mold
    Join Date
    Feb 2021
    Location
    whitehall,wi
    Posts
    14
    richhodg66 have you any good test with sns 158 coated boolits using 700x ? im just starting and can use any advise what to look for.

  20. #20
    Boolit Master
    Join Date
    Jun 2012
    Posts
    760
    Quote Originally Posted by abunaitoo View Post
    I've been trying out IMR700x in my SMLE and 2A.
    303- Lyman 314299 GC, un-sized, RP, no filler, Larz carnuba red lube.
    9.0gr- 50yds- 1" to 1 1/2". 100yds- 2" to 3", 7" low.
    10.0 gr- 50yds- 1" to 1 1/2". 100yds- 2" to 3", 5" low.
    308- Lee 185g sized to 309, GC, RP, no filler, Larz carnuba red lube.
    9.0gr- 50yds- 1" to 1 1/2". 100yds- 2" to 4", 6" low.
    10.0gr- 50yds- 1" to 2". 100yds- 2" to 4", 4" low.
    I'm going to try a 311 bullet in the 308.
    Seems like I could use more powder. I read somewhere the max is 14.0gr.
    Recoil was mild. Very clean burning. No primer pressure signs.
    I'm wondering if anyone else has used this powder????
    I did a search and didn't find much.
    For me, it seems to work better than Unique, Red dot and Blue dot.
    <<<<<<<<<<<<><<<<<<<
    Lyman Cast Bullet Manual no 3 is Free online if you Google it.Its a pdf so you can download the whole thing free.
    Also check out
    www.cornellpubs.com
    for reasonable priced reprints of Ideal and Lyman manuals from the 1920s thru today .hundreds of titles.
    Also 2nd and 3rd Lyman Cast bullets manuals available.Good reprints.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check