$55 430-310-FN (Lee Copy improved)

[338RemUltraMag]

Will the plain base version weigh the same as the gas checked version?
Can all cavities be plain base?

The PB option will raise weight but only by 2 grains or so total because normally a gas checks would be sitting there.

Updated!

[44MAG#1]

If the bullet is plain base will the one lube groove carry enough lube for full loads?
If not, I am interested in the gas check version but, if the lube capacity is enough for plain base I would prefer it due to the cost of the gas checks.

[338RemUltraMag]

If the bullet is plain base will the one lube groove carry enough lube for full loads?
If not, I am interested in the gas check version but, if the lube capacity is enough for plain base I would prefer it due to the cost of the gas checks.

I would say so, most of the lube will be in the large groove, the check will be ~ .070 tall which only leaves a sliver of lube in that back groove. I agree copper checks are expensive, but I will be offering my 44 cal Aluminum checks with a mold purchase for $22 per thousand.

[xpaholic]

put me down for one each 434, 454, and 480. all $55. sets, all GC'ed with top punches for each. I'll let you know about how many of your GC's I want when this closes. thanks xp

[338RemUltraMag]

Updated!

[jason f]

i will take a 2 cavity gc .434

1000 aluminum checks to go with it.

can you take my name off for group buy, but i still want gas checks. you can send me an invoice for checks at jasonfancher321 at gmail dot com. thanks jason

[jason f]

can you take my name off for group buy, but i still want gas checks. you can send me an invoice for checks at jasonfancher321 at gmail dot com. thanks jason

nevermind the gas checks, i will find some somewhere. never did get an invoice to pay for them. you must be very busy.

[338RemUltraMag]

Updated

[338RemUltraMag]

nevermind the gas checks, i will find some somewhere. never did get an invoice to pay for them. you must be very busy.

Jason,
Hey sorry I didn't see that you wanted gas checks until now, if you still want to buy them from me, I will take care of you! Shoot me a pm and let me know.
Joshua

[tygar]

I'll take one in .460 with top punch.
THanks
Tom

[War Eagle]

I will take one. Make mine a .434", 4 cavity, all gas check

[44MAG#1]

If the crimp grooves will be deeper than the horrid crimp grooves on a lee bullet especially their first 310 gr RNFP-GC I will take a 2 cavity plain base. If the crimp grooves aren't any better I will stick with the Lee that I have. Be sure to let me know as if they are better I want a mold.

[War Eagle]

Going to have to scratch my name from this one. I decided to go a different route.

[gutpile]

I am in for a 2 cavity .432 top punch and 1k gas checks

[ermont]

Put me down for one .432 and one 454 both 2 cavity PB

Eric

[338RemUltraMag]

If the crimp grooves will be deeper than the horrid crimp grooves on a lee bullet especially their first 310 gr RNFP-GC I will take a 2 cavity plain base. If the crimp grooves aren't any better I will stick with the Lee that I have. Be sure to let me know as if they are better I want a mold.

The crimp grooves are deeper and more pronounced than the Lee mold. I'll add you to the list, you can just update to confirm you want one and what size you would like.

[44MAG#1]

I want a gas-checked 2 cavity that drops a minimum of .432" Let me know the info you need. I have Pay Pal.

[Cowboy_Dan]

I'll take one in .460 and one in .432. Both 2-cavity.

Would they both take the same gc's?

[AlaskanGuy]

We should be getting close on this one????

[sisterjim]

Will this boolit chamber in marlin 444? I haven't got the chamber dimensions on hand and away from home?