MiHec 360640 Light brass four cavity HP or four cavity solid

[Low Budget Shooter]

Woohoo! The wait has been so long, I can hardly believe it's finally done. I don't think I've ever turned over $100 so happily in my life.

[dragon813gt]

829 days from being the first to sign up to sending payment

[rintinglen]

Holy moly! it's here at last. On the plus side, the decline of the euro in value means that this one will cost me a smidgen less than than last, if the Paypal Currency converter is to be trusted.

[AZBrian]

Received Invoices for both moulds and made Payment for each.

A long wait for this one - will be very happy to get them!

Thanks!!
AZBrian

[GLL]

Now the wait for the 361627 !

Jerry

[g.man10mm]

Awesome, paid.

[wonderwolf]

Excellent! Paid! Thanks again....what mold is next on your list MiHec?

[Stick_man]

Invoice has been paid! Looks like Christmas in April or May this year. Can hardly wait.

[rockydoc]

I would like a 4 cavity Cramer with plain base and large hp and solid pins.
harley dot rock at knology dot net

I placed my order 11-4-14 and received notice the order was ready and sent my payment 4-17-15. Approximately 6 ½ months, that's not too bad. How long does it take for an order to arrive from Europe?

[MiHec]

I placed my order 11-4-14 and received notice the order was ready and sent my payment 4-17-15. Approximately 6 ½ months, that's not too bad. How long does it take for an order to arrive from Europe?

In normal conditions - around 14 days

[LabGuy]

I just got mine!

[Low Budget Shooter]

Got mine today, too. Thanks 45 2.1 and Miha! LBS

[rockydoc]

I placed my order 11-4-14 and received notice the order was ready and sent my payment 4-17-15. Approximately 6 ½ months, that's not too bad. How long does it take for an order to arrive from Europe?

I received the mold today, 10 days after payment. Not bad. I am pleased with everything: what I got and the amount of time it took, except it came with no instructions. This is my first brass mold, so are there any special preparations to do to get it ready to cast other than lubricating the alignment pins and sprue plate hinge?

[Stick_man]

Got mine today. Can't wait to try it out, although it will likely be a little while.

Rockydoc, I scrub my mold and pins down real good with brake cleaner, then hot soapy water, then brake cleaner, then one more time with the hot soapy water. Rinse it off well and let it dry. Then install the pins that I want to use and lube the key points. Then I do a couple cycles of heat and cool. One more touch of lube and I am ready to start casting. I preheat my molds on a hotplate. Usually getting nice pretty boolits within just a few drops.

[WARD O]

Received mine today as well. Looks perfect as always! Thanks again for a great mould.

ward

[Jlamont2020]

360-640 and his little brother 360-640L

20:1 about 146gn and 126gn respectively with the deep cavity pins. Now another excuse to buy more lead.

[paul h]

I was pleasently surprised to find a package on the kitchen table containing another beautiful MP mold last night!

[paul h]

I received the mold today, 10 days after payment. Not bad. I am pleased with everything: what I got and the amount of time it took, except it came with no instructions. This is my first brass mold, so are there any special preparations to do to get it ready to cast other than lubricating the alignment pins and sprue plate hinge?

The only difference I find with brass compared to steel and aluminum is it seems to be a bit more finicky with temperature, i.e. not to hot, not to cold but just right. Just give it a nice pre-heat and as with any other mold give it some time for you to find the right temp and cadence. If it's your first hp mold, beware that you need to cast fairly quickly to keep the heat in the pins so that you get a complete fill out.

[MiHec]

I have some overorder molds. If you want one send me PM

[rintinglen]

It got all the way from Slovenia to Huntington Beach where some feckless illiterate postal employee managed to mislay, or mis-deliver it. This positively stinks.