LOL!
How true.
"A cheerful heart is good medicine."
hi gang after reading this thread i tumbled lube some 45rn in JPW shot at 800fps was 30min cleaning lead out of my barrel thanks but no thanks clint
And yet I've shot 2000 FPS gaschecked boolits lubed with JPW out of my K-31 Swiss and .300 Weatherby Magnum Vanguard without leading. Boolit fit, alloy, bore condition, all the usual suspects come into play as well as lube. JPW's not the all-purpose lube for everything, though.
"A cheerful heart is good medicine."
casting acww . .452 nice smooth bore boolit drops .4525 clint
Ditto what Ricochet said. Clints folly what alloy were using and what was its BHN?
do not bhn air cooled ww can just mark with thumbnail clint
Hi guys I'm a new member and new to casting and reloading...I've been reading the board for awhile now and have learned a lot...Thank you...
I would like to know what you guys think about using a small deep fryer set at a low temp say 150 to 200 degrees f with JPW put a couple hundred boolits in the basket put it in the now melted wax. Leave it in the wax for a couple of minutes so the boolits can warm up enough for an even thin coat..Then dump on wax paper... The fryer I'm thinking of using has an airtight sealable lid so I could just leave the wax in it and use it as needed...What do you think?????Thanks Daryl
I know you guys like tumble lubing, but has anyone cooked out the solvents and made a lubrisizer lube out of this? Maybe soften it with boolplatelube?
Update on the deep fryer....It works great..The temp setting might be off alittle but I set it on 300 covered the bottom of the basket with boolits 165 of them (45acp) and set them in the fryer for about two mins. Lifted the basket and let drain took the boolits out with my fingers they were warm but not too hot to handle..Put a nice coat on the boolits...The only down side is the vapors...Very strong but I'm thinking ( hopeing) the solvents will bake off...By the way I got the jpw at Lowes for $4.85 a can. I bought four cans put two in the fryer it should last a long time..
Now you've gotten me thinking...
I wonder if a Crockpot would get hot enough to do the same job with JPW?
Way, way, way more than hot enough.
"A cheerful heart is good medicine."
Realize that I am dragging up a farly old post here. But I wanted to put in my $.02 in favor of JPW. For my low velocity plinking loads in 41 mag I have been doing the LLA/size/more LLA route. But this time I went with LLA/Size/JPW. This gun tends to lead up at and just in front of the forcing cone. Although still present, it was substaintially reduced with the JPW. For the record I was ACTUALLY using an old can of "TREWAX" that came with the house when I bought it. But I am pretty sure they are both simply carnauba based floor waxes. Kev
JPW has a little carnauba wax in it, true. But the solid stuff in it's mostly microcrystalline paraffin wax, and about 80% of it's mineral spirits. Trewax has a lot more carnauba.
"A cheerful heart is good medicine."
After reading through this thread, I'll be going out Friday(my day off) to find some JPW.
The old, old can of trewax I have says over 50% carnauba. i add a small amount to my fwfl. Gianni
[The Montana Gianni] Front sight and squeeze
I have some old carnuba car wax. "mequiars gold class"
Could I just use this to lube a bullet?
If so, could I just get some on my fingers and push it into the lube grooves myself?
Thanks!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |