Just as a side note, do these come with the penta pins too?
Just as a side note, do these come with the penta pins too?
Gunsmoke4570
I'm guessing no pentas. The penta requirement on other group buys was something like 30 molds as a minimum to get the pins made. It was never expected that this buy would be anything different than a re-run of the previous run, except that (with the exception of the one two cavity mold, Miha's own test mold) this will be four cavities instead of the original two.
Sorry to disappoint.
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
Not a problem. If it was an option I wanted to add it, but I can make do 8)
Gunsmoke4570
I'd like a four cavity 380 mould, please.
Doc
Bodydoc447 at aol dot com
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
A 4 cavity mould is 2x better than a 2 cavity mould, RIGHT???
Chalk me in for a 4 cav .380 please - salmon hyphen boy using comcast for net...
(Thinking I should bite the boolit and put in an order with Miha for one of every mould he makes.. It might be cheaper!!)
"Unnh, Negative. I am a meat popsicle."
Chuck
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
If possible I'd like an extra set of pins for my 4-cav. Turning the pins over works poorly on my pre heating hotplate. I'd rather pay for a set and grind the points off for solids.
Cheers and thanks DukeInMaine for doing this.
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
Not real sure how this paypal thing works. I have used it for ebay and to send moneys to people I buy from, I'm guessing you just use my email addy? If so it's mscornette AT hotmail dot com.
When you pay something with paypal (as you say that you have in the past), they send you a confirming email. That email address (that they send the confirmation to) is the correct one.
When the molds are ready, Miha will send notice to PayPal that he wants them to collect the mold cost from you, and will give them your email address. They will send the "invoice" notice to that email address, asking you to pay. When you pay, they will collect the $$$ from you, and place it in his account, keeping a transaction fee for themselves. It works fine. I've paid Miha dozens of times now this way.
So, if that's the address that you referenced, then I'll use that one for Miha.
Last edited by DukeInFlorida; 07-25-2011 at 06:42 AM.
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
Put me down for a 4-cav 380 mold, please.
patsher at tribcsp dot com
Thanks!
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
I heard back from Miha, confirming that he will be supplying the blank pins.
He points out that the blanks, and the regular round hollow point pins on this mold are designed differently than the "normal blank pins". Please visit the opening post (OP), and click on the image of the mold for the large image of the original run (two cavity molds). There you will see the design of the blanks (makes a flat nose, and the back side is flush with the back of the mold), and also the hollow points.
We'll be getting BOTH sets of pins.
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
In that case my wish for two sets was already fulfilled. No need for extras and my bad not reading up good enough and asuming they were for turning over.
Keep up the good work Miha and DukeInMaine!
This is gonna be a snappy little pill for my 9's..
NP.
One of the things I like about Miha's molds is that he bends over backwards to give people what they want.
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
Put me down for one 4-cavity 380 mould.
alexdoug [at] sbcglobal [dot] net
Thanks,
Alex
Meddle not in the affairs of dragons.
For you are crunchy, and good with ketchup.
NRA Life Member
SASS #87220
_______________________________________
Gotcha covered. Thanks.
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
Author of a book on reloading
ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
NRA RANGE SAFETY OFFICER
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |