NOE 225107 37Gr. hornet/5.7

[Bullshop]

I want mine yesterday.

[tonyjones]

I understand NOE is pretty much booked-up through May. Let's go ahead and get in the schedule. That leaves plenty of time for more folks to sign up.
Tony

[kbstenberg]

I was wondering when funds will be due. Its my determining factor in signing up.
Kevin

[troy_mclure]

so somebody throw out a date! lol

[Landric]

Swede's schedule is full until May or so, May would be the absolute earliest it could run, so I suspect funds would be due in May or later.

[Hickory]

I've been lookin' the drawing over for this boolit and was wonderning if a hollow point would be necessary and if it was to be done it might be best with a pin about .120" in diameter and with a radius the same as the diameter of the pin.
With it making the hollow point no deeper into the boolit than .125"

Just my thoughts on the matter, what say you all?

[troy_mclure]

so we need to get booked soon so we dont get pushed back till aug.

[SwedeNelson]

troy_mclure

Thanks you for starting and honchoing this buy.
We are on the schedule for May and I hope the shop can better that.
Keeping my fingers crossed, and they are doing a great job.

We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.
Prices will be as follows:

This buy will be on our SB (Small Bore) moulds.
This is a down sized mould for better heat control.
We will also offer it in a 10 cavity double sided mould (DS10-SB)
The DS10-SB can not be hollow pointed.

Prices will be as follows:
Single cavity mould (Standard Size mould) $68.00 Ea.
Double cavity mould (2CSB) $72.00 Ea.
Three cavity mould (3CSB) $79.00 Ea.
Four cavity mould (4CSB) $85.00 Ea.
Five cavity mould (5CSB) $92.00 Ea.
Ten cavity mould (DS10-SB) $160.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $10.00
Prices are subject to change at any time.

You can mix number of cavities in an order to make 15.
We will offer gas check only on this bullet.

Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal acount:
pbsco1@qwestoffice.net
Make checks and money orders out to:
Night Owl Enterprises

Our mailing address is:
Night Owl Enterprises
1645 W 150 N
Provo, Utah 84601
801 377-7289

Zip Code List of payed orders
1 70360
2
3
4
5
6
7
8
9



Thanks again
Swede Nelson

[SwedeNelson]

It looks like there is some interest in a PB bullet.
The PB would have a larger than normal band,
but we can do it if you want.

Thanks
Swede Nelson

[troy_mclure]

nice!, of course im already impatient for it! lol

[bearcove]

so are you guys wanting this to be a short run on this buy, and get our moulds in line to be made, or do you want to wait a couple of months and let more people join up?

If its on the production list it goes when its turn comes up. Anyone else can buy from swede after, out of his extras.

[Bullshop]

Can we pay now to avoid the embarrassment of being broke at the critical moment?

[troy_mclure]

ill hold the money if you want.

[NoZombies]

Swede, how large will the band on the PB design be?

Knowing the date tells me that I'll be in, now it's just a matter of what the PB option is, and how many cavities.

[Matt3357]

Yeah, I'm in if it is that far out. I'll set some aside just for it as it comes in. Not sure on the cavities yet, I'll have to give it some thought. Any ideas on how fast the PB could be pushed in a 1 in 12 twist? Would make a good reduced load for my 22 hornet.

Matt

[SWIAFB]

I'll in for a five cavity.

[SwedeNelson]

We will always take money.
You just will not get a PM with the total cost figured out.
But not hard to do, Just read post #28 above.
Will start a Zip code list as soon as I start to get payments.

As to twist rate it has a history of shooting great in hornets
so the slower rates should be good, 12", 14".
You could play here too:
http://www.tmtpages.com/twistrate.htm
Some one with more experience may chime in.




Swede Nelson

[NoZombies]

Okay, I'm in. Mark me down for a 5 cavity, 4 GC and 1 PB, and please HP one of the GC cavities.

[Hickory]

If Swede's gonna do a plain base also change my order to 3 cavity
One pb, one gc and one hp w/ gc.

[Matt3357]

Couple of questions for Swede. What is the approximate weight of the hollow pointed bullet and is the pin provided capable of producing flat point bullets as well or is that cavity strictly hollow point only?

Actually, would it be possible for some one to post a picture of something similar to what we are ordering here with a HP setup? I have never seen any of NOE's molds.

Thanks,
Matt