Search:

That is OEM compensated shroud. "HV4C" Heavy Lug, Vented, 4", Compensated Its from the Norwich NY plant

I wouldn't bore the .32 cylinder- see if DW has another.... as you know the .32s are far and few between as well.
I have many DWs including blued and stainless in 22mag, 32mag, and 32-20. My goal...

I have a few different moulds and I think one of them throws just over 100 gr. I'll experiment- thanks for the info.

I usually don't post on CB; I use the site to learn but I have to share my recent acquisition. Been looking for a stainless DW from the Monson MASS plant, in 32-20, for several years... Three...

Good choice. I like shooting all three but recently picked up one of the original runs of .44 Mag. Winchesters are like potato chips; you can't stop at one....

The Palmer plant produced some fixed barrel 357s.

I have a few other DWs, to include some pork and a few PMs. They just don't "fit" in the collection pictured above...

I don't post often- mostly just read but since I took a pic of my cash cows for the DW Forum, I thought I'd share it here as well and put out a feeler to fill the holes in the Monson collection. I...

I had LBT make a .375 wfn gc mould that casts at 230 gr. using coww. I wanted something close to the HDY 220 grainer and this is what he came up with. Shoots pretty well.
156501

Supposed to be .45-70 but looks like an aftermarket barrel with a quarter rib, so I'll cast the chamber to ensure dimensions. Really looking forward to getting it. I have a Pedersoli cavalry...

Not here yet- somewhere on a Brown truck or plane... should be at the house on Wednesday. Don't know what all I have until it gets here but what I think I know is that it's a Griffin & Howe...

Glad you are OK! I have multiple shot shell presses set up and use a piece of masking tape on the powder bottles to mark current powder and settings. May help you in the future. Again- glad it...

I used a dusting of HF Red from a Qtip for my "Zombie" boolits.
121121

Thanks for the replies. I heat-treated and then DTPC-ed some 10mm this weekend. I'll get them loaded up and give it a go.

I did a search but most threads were approaching a year old. Any more on shooting PC through ported barrels? Someone had an issue with white residue and others mentioned some residue...

USPS is...

Found that place last night- thanks. A lot of information on heavy for caliber 10mm that I hadn't seen before.

Here is the boolit: I'm using TAC#1 for lube. I'll have to fill the seating stem with hot glue when I start working loads for accuracy...
118986

Ah yes- I forgot; the launch pad is a Dan Wesson PM7-10. It is a fully supported chamber. Not looking for nukes- just a nice woods round for whitetail and hogs. I'll do some more searching- the...

Before I pull the trigger, I wanted to run a sanity check with you more seasoned members...

Lacking any industry heavy load data for the 10mm, I read what I could find and determined (in my mind)...

I'd like to read so I have a reference for loading my 450 Martini and 577 Snider, which are OEF bringbacks that I haven't loaded for (yet).

SOWELA (southwest Louisiana) had 3 to 9, depending on location, since Thur nigh. High temps only reached mid 80s. Only 70 this morning and the typical afternoon chance of more rain. That front was...

I removed Alox with Acetone. I placed a few handfuls on an old towel, poured a bit of acetone over them to wet and shook back and forth. Came out clean as a whistle. Coated 10 minutes later then...

Perfect- thanks. I needed one to use 1-1/4" dies. This will keep the Snider and Martini well fed.

I thought about honing it out; 1) not certain how hard the steel is and 2) concerned about making it out of round. I know there are some folks on here that are handy with a lathe- hoping someone can...

Does anyone make/modify seating stems for the HDY New Dimension dies? The floating seating stem seems too small and I can't open up the ID with the tools at home.
Now that you-all have me slugging...