I had a lyman devastator until I got this. I sold the devastator. That penta cavity is absolute money. I have a '92 Puma in 454 casull. Most of the time I'm feeding it this at around 1200 ft per...
Type: Posts; User: Maximilian225
Forum: Cast Boolits
I had a lyman devastator until I got this. I sold the devastator. That penta cavity is absolute money. I have a '92 Puma in 454 casull. Most of the time I'm feeding it this at around 1200 ft per...
Forum: Cast Boolits
I have one of the original runs of this mold when it was a two cavity group buy on here. Mihec does incredibly good work. It casts good boolits very easily. Congratulations. That's also a very...
Forum: Cast Boolits
[emoji23] [emoji23] I laughed way to hard at this. [emoji23] [emoji23]
Sent from my Nexus 7 using Tapatalk
Forum: Leverguns
I have a Rossi 454 and absolutely love it. I run 45 Colt in it ranging from really light cast loads to heavy jacketed Ruger /TC loads. I have never actually fired any 454 in it, but the previous...
Forum: Cast Boolits
I never could get the swc to function properly in my XD45. The head of the round being extracted would always catch on the mouth of the next round in the magazine. Maybe I had them seated to deeply.
Forum: Cast Boolits
+1, Exact same setup
This gun will not feed semi-wadcutters though. The extracted rounds rim hangs on the next round in the magazines case mouth. It reguires a HP, RN, or RNF profile. The Mihec...
Forum: Reloading Equipment
I use a dehumidifier to keep my basement below 60%. Seems to be around the magic number where surface rust ceases. It is only a problem for me in the summer.
-Max
Forum: Our Town
This answer is somewhat office dependent. It is true your carrier has an individual scanner that they use to scan all DC packages.
Some offices scan packages "recieved at facility" on arrival.
...
Forum: Our Town
As another employee of Big Blue. The short answer is management at the higher levels has forgot or chose to ignore that service is the only thing we sell. They are so bent on cooking the books to...
Forum: Our Town
If I remember correct Lee charges a flat shipping of $4.00
-Max
Forum: Swaging
David Corbin's book recommends boiling the cases in water and detergent followed by a second boil in plain water. Than baking in a 600 oven for 20 minutes to dry and anneal before drawing.
-Max
Forum: Our Town
This place has cost me many, many hours of sleep. [smilie=1:
-Max
Here Ya Go! ;-)
http://i456.photobucket.com/albums/qq289/Maximilian225/Lee%20Molds/DSC01793.jpg
http://i456.photobucket.com/albums/qq289/Maximilian225/Lee%20Molds/DSC01792.jpg
They don't...
Forum: Our Town
Brass is Privi Partizan. As BillyB said modern ammo.
If he should change his mind Grafs sells this brass for 46 per 100.
- Max
http://www.castpics.net/molds/Beagling.htm
http://www.castpics.net/memberarticles/Bullet%20Diameter%20Enlargement.htm
-Max
http://www.castpics.net/molds/Beagling.htm
http://www.castpics.net/memberarticles/Bullet%20Diameter%20Enlargement.htm
-Max
1st off I use a bottom pour pot. Never tried this with a ladle.
I cast the mold up to a hot temp with a couple of 1/4 x 20 nuts lying on the edge of the pot. After the mold is throwing frosty...
Forum: Leverguns
I cannot speak for the 45-70, but my experience with other calibers is Starline is superior brass hands down. Flash Holes have no burr, cases are all very close on length. If they made it for...
312-185 & 312-155 most 30 cals with sizing.
+1 on the 452-200RNFP. It also feeds in those Auto's that don't like SWC.
-Max
:lovebooli
Forum: Our Town
The other three pounds is rope to hang yourself with.[smilie=1:
-Max
Forum: Military Rifles
I load mine to commercial action pressures in the load manuals. There is nothing weak about the 96 Swede action. Kimber also loaded them in other high pressure cartridges. PO Ackley did some...
Forum: Military Rifles
I have a Gustav 96 that I have sporterized including glass bedding the action. It will put 95g V Max's into .5 inch at 100 yds with H414.
-Max
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |