Those were set up for inlines to have a more contained ignition. They required modifications or replacement of the inline striker for use. I believe they were marketed for pre 209 primer knight...
Type: Posts; User: fixit
Forum: Muzzleloading.
Those were set up for inlines to have a more contained ignition. They required modifications or replacement of the inline striker for use. I believe they were marketed for pre 209 primer knight...
Forum: Military Rifles
80,000 PSI? While the design of the cartridge is intended to offset pressure incursions, I would be worried that when the inevitable happens, the result will spectacular! There is a reason that...
Forum: Our Town
My dad spent the first half of his youth in southern Kentucky, with the second half in Mooresville Indiana, some time around the 1930s. Now this also happens to be John Dillinger's home town. My dad...
Forum: Cast Boolits
I have a Grendel bolt gun (ruger American with the long barrel) and it's all I'm likely to need here in Indiana. With a 200 yard point blank range, I don't expect to have to push beyond its limits....
Forum: Deep Theological Discussion
The process of building my current church was full of miracles! One of the most fascinating was when we were in need of a drainage tile to be in place to meet the county's zoning requirements, only...
Forum: Gunsmithing Tips & Tricks
One of my great regrets was passing on a 16 ga. M37 that was a friend's trunk gun! It was around 1978 or 79, and he wanted 40 dollars for it..... I passed it up because it was a 16, and l didn't have...
Forum: Deep Theological Discussion
Having studied somewhat in the judeistic side of things, it's worth noting that prior to Jesus' resurrection, the saints were believed to be sent to a place referred to as Abraham's .bosum.... kinda...
Forum: Deep Theological Discussion
It is worth noting that the medium at endor reacted with a cry of surprise when Samuel came up..... this suggests that she was not accustomed to seeing the actual spirits, but rather counterfeits....
I have an older super Blackhawk with a soldered front sight, and I have a problem with the front sight height.... with the rear adjusted all the way down, it hits high, several inches worth. My...
The more I think about it, the more likely I'd be going with a 400 grain or more flat point for penetration and b.c.. The longer slug should retain velocity better, even with a flat point. Oh, how my...
Forum: Cast Boolits
In some of the states that have cartridge length rules, people would trim their 45-70 brass to the max length to get by the regulations. I've got 20 rounds of it that have been trimmed to slightly...
Forum: Black Powder Paper Patching
Something I've done is to use a priming charge of black powder.... about 10 grains. I've had ignition problems with a couple of rifles with the subs, and not wanting to just dump them out, plus the...
Forum: Deep Theological Discussion
One thing to note is that the Bible is largely a legal document, a testament, of God's promises to humanity, and how He will deal with humanity and it's actions, both good and bad. As such, there is...
One of my greatest regrets was selling my six inch stainless security six.... In a moment of insanity, I figured I needed the money more than the gun, and the rest is history. It was bought new and...
Forum: Gunsmithing Tips & Tricks
I have a 14 inch 30-30 barrel for my contender, and while it shoots ok, I have read about out of square crowns and chambers on these. I am aware that my factory crown is not pretty, as it is...
Forum: Leverguns
I had a 9422m, the magnum version, and I allowed myself to get finagled out of it by a friend after I backed into his car..... that he had parked across the driveway. He had always lusted after that...
Thank you, guys...... this is the line of discussion I was hoping for! Keep it up!
I don't recall the load, but I had some 340 gr. Lee bullets that I had loaned kinda hot with 4198...... In my H & R.... let's just say I did some load re development! First shot was met with an ouch,...
Forum: Muzzleloading.
I bought one of those factory new way back when, and it came with a short starter that had a ramrod length rod attached..... pretty much a purpose built tool. It wouldn't be hard to duplicate.
Forum: Our Town
We fish ewe a mare egrets moose, panda hippo gnu deer! (Thanks for reminding me of that, jdfoxinc!)
Forum: Gunsmithing Tips & Tricks
From my viewpoint, many of bench lathes found are handicapped by limited headstock clearances! To my knowledge, all of the 7" lathes are limited to about .800" clearance, which ain't much! When I...
Forum: Case Forming / Re-forming
I agree with the partial full length.... just a little resize of the body, and you get a neck size in the bargain! If they get too snug, I'll go and bump the shoulder, but otherwise, it's good.
Forum: Our Town
I guess they're really 'dangling bits' out there for safety!
Forum: Cookin' Recipe's
I like many forms of chili....as long as it's not sweet! That said, my toppings are typically shredded cheddar or Mexican cheese and sour cream, maybe some Curry powder, lotsa pepper, maybe...
Forum: Deep Theological Discussion
Reverent fear, which is a basis for honor of The Holy One, is just the beginning of showing correct respect for the name of God, and yes, He is correctly referred to by many names. We make a grave...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |