Thanks Dutch.
Type: Posts; User: Sooner
Forum: Military Rifles
Does anyone know the screw size for the Swede 94 rear site base screw? I’m assuming it’s something metric. Looking for a replacement locally.
I have a 270 mr die and a expander die with .277 expander. I would like to trade for a 7mm (Mauser) mr die and expander die and 285 expander for 7mm Mauser.
That is great! I signed up for the forum and am waiting on approval.
I was looking for the dies for the hand tool but don’t know what die numbers correspond with which cartridge. I am looking to buy a set. But those mold pictures in your link were great! Thank you.
Does anyone have a list of the modern bond die numbers and the cartridges they are used for?
Thank you.
Does anyone know the thread size for the Modern Bond hand tool dies? The large diameter Lyman model 10 dies start and are close in diameter but the thread pitch is different. Thank you.
Edited to...
Forum: Cast Boolits
Thanks for all of the suggestions. I’m going to try and fab one up.
I have a large brass Modern Bind Gand tool. It looks like a large 310 tool. It takes larger dies than a 310. Does anyone know where I can get dies? It is really well made snd heavy snd I would like...
Forum: Cast Boolits
I have a 311299 hp mold from Lyman. It didn’t come with the pin. Has anyone fabricated a cheap replacement pin? Looking to try the mold on the cheap without sending it off to get a new pin made....
Ndnchf
Did you turn the lower threads off of the bolt? That is a great idea.
How repeatable / accurate is the Lyman trigger pull gauge. Is there a better tool for around the same price?
Forum: Cast Boolits
I like the 452423 Lyman style. A little lighter than you are looking for but runs great from many 1911s
Forum: Cast Boolits
Additionally H&G molds are very nice (this is my first and only H&G mold) like I’ve always heard.
Forum: Cast Boolits
This bullet doesn't look like it has a crimp grove. Anyone have any experience with this one. It is better to crimp in the top lube groove or possibly taper crimp. These will be for 38 sp target...
Forum: Cast Boolits
Thanks! That will save some experimenting .
Forum: The Star Equipment Corner
I’ll check out the rcbs. Temperature adjustment is a big plus
Forum: Cast Boolits
Don
What velocity works with that alloy? 860-950 ish?
Thanks again
Forum: Cast Boolits
Thanks for the input guys. I think I’ll go with the hp version. What alloy are you using?
Forum: Gunsmithing Tips & Tricks
I’ll give sandpaper a try to knock the teeth down on one side. Great advice from everyone.
Forum: Cast Boolits
I’m thinking of getting a heavier mold for my 45 Colt. I’m thinking the NOE or MP version of the RCBS 270 SAA. Are there any other I should be looking at? Also should I get a HP version or is it more...
Forum: The Star Equipment Corner
I’m going to look into the Star and Lyman heaters. My Star is in my unheated shed and it can get pretty cold here in Oklahoma. Especially trying to use harder lubes.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |