I will have shoot mine for a group to see. At 25 yards they are all touching, that’s the furthest I have shot it with a target. Mostly I shoot steel out to about 75 yds
Type: Posts; User: milsurpcollector1970
Forum: Coatings and Alternatives
I will have shoot mine for a group to see. At 25 yards they are all touching, that’s the furthest I have shot it with a target. Mostly I shoot steel out to about 75 yds
Forum: Coatings and Alternatives
Or you could go with a RDB system that CMMG developed and no more lead on the tail of the bolt
Forum: Our Town
I shoot at a private club with over 1000 members, they are strict there and will kick you out if you violate the rules or give one of the range masters a hard time.
I have no problems with that...
Forum: Cast Boolits
I have the Lyman 314299 bullet which is an excellent boolit do you want any?
Forum: Cast Boolits
What are you using for a magazine? Many of those wildcats are cool but for me getting them to run through a magazine was the problem.
Forum: Cast Boolits
I use the NOE 357-190-RF-06. Works well in the AR
Forum: Cast Boolits
The Lyman 314299 makes a good subsonic round. No issues with feeding either
Forum: Cast Boolits
Thanks everyone
I am pulling all my 300 Black loads and starting over with AA#9 data, whats interesting is I have used it in other catridges with H110 data with no issues. 44 mag, 38-55
The...
Forum: Cast Boolits
I recently started loading for 300 Black with surplus wc820
Im using H110 data with Lee 180 and Lee 160 gr
I am using 18 grains with the Lee 160 gr and 15 gr with Lee 180
I am getting blown...
Forum: CB Loads / Military Rifles
Like others have said, I would get leading around the tail of the bolt. Powder coating is kind of a PITA but if its setup right its much faster than convetional lubing
Forum: Leverguns
The inside looks ok, I will push a soft lead slug down it to test
Forum: Military Rifles
Its also not a low number, Remington never made any with heat treat problems.
Forum: Military Rifles
Original finish was dipping the rifle in oil when hot (not sure what oil was used)
Forum: Cast Boolits
I have had nothing but problems getting the 300blk to chamber in the ar with cast also had issues with the 30 hrt (a rimless 30 herrett made from 6.8 spc cases)
I finally gave up on 30 cal cast in...
Forum: Cast Boolits
I wasn’t concerned about squeezing all the lead out. I assumed you wanted it out to get the best price from the scrapyard. Lead contaminated copper doesn’t bring as much $$
Forum: Cast Boolits
Did you get all the lead out of it. I reheated my jackets and dumped them out on a screen, got another pound of lead out of them I need to clean mine but I only have about 2 pounds.
Forum: Cast Boolits
I cut a shower pan up with a hatchet, try cutting or chopping first sawing gets lead chunks everywhere. Hammer and wedge is good idea too
Forum: Leverguns
I threaded and profiles a 38-55 barrel, It wasnt as easy as a AR-15 barrel but not super difficult
Forum: Cast Boolits
Well, a few things could be happening.
You could be leading your barrel because of the velocity Not sure what the book speed is for that charge could not find it in the online reloading guide.
...
Forum: Factory & Surplus Powder
Casefull of 5010 with Lyman 314299 in 30.06 goes around 1600 fps makes an accurate target load
Forum: Leverguns
I have a confession, Im 50 years old and have never owned a center fire levergun. To remedy this I am building a Marlin 336 in 38-55. Back before the price on guns went throught the roof I bought a...
Forum: Cast Boolits
I have a ops inc brake on my MK12 mod 0 clone The baffles are vertically oriented. It’s a little louder but not much .223 cal I don’t need it but it’s part of the clone look.
Courtesy at the range...
Forum: Hunting with CB's
I built a 9mm ar, I was getting around 1600 fps with 115 gr fmj.
These were carbine only loads You could easily get a hunting boolit going fast enough to kill a deer
But I have other guns which...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |