The results were mixed. The lubricant itself seems to have done well. Problem is that I made it stiff for higher temperatures. On range day, we had a cold snap and I was shooting in sub 50 degree...
Type: Posts; User: jld_in_IA
Forum: Boolit Lube !
The results were mixed. The lubricant itself seems to have done well. Problem is that I made it stiff for higher temperatures. On range day, we had a cold snap and I was shooting in sub 50 degree...
Forum: Boolit Lube !
Battis,
The lube stick idea is great. Should be equivalent to the preformed grease seals that wonder lube sells. I can easily do something similar with 3/8 tubing instead of using the revolver...
Forum: Boolit Lube !
Thanks for all the suggestions. I’m going to try the bees wax and crisco.
Seems like from the reading I’ve done about 5 parts bees wax and 4 parts crisco is a good place to start. If it is too...
Forum: Boolit Lube !
Hi all,
I’m getting ready to break out the BP cap and ball revolvers for a range trip. Discovered I am out of wonder lube and can’t get more locally.
Instead, I was hoping to get a...
Forum: Reloading Equipment
I don’t know the 3 hole version, mine is a 4 hole. Look inside the turret head for a detent ball. That should keep the turret from rotating when the bar is removed
Sent from my iPad using...
Forum: Reloading Equipment
I've used the Lee Loadall, and the Mec. I won't say the Lee was bad, but it was slow and not flexible for varying load requirements. Particularly crimps were difficult with some hulls. That is...
Forum: Cast Boolits
Thanks all for the suggestions. It sounds like trying to work with the 223 in an AR platform is a tricky proposition for cast boolits. Far from impossible, but not necessarily the task for a...
Forum: Cast Boolits
Larry,
You make an excellent point that I was not very clear about my goals. To be more reasonable about it, let's say 1 MOA at 100 yards, and 1.5 at 300. The rifle will do that with good...
Forum: Cast Boolits
Hi all,
I've never tried casting for rifle before, but am considering a mold to cast for my AR-15 in 223 Remington. The goal for this rifle is paper punching target accuracy, and a boolit that...
Forum: Helping Hands
As a relatively new caster, I'll put down some of the most important lessons I've picked up.
1. Smelting lead is an outdoors operation. I don't care how good your ventilation is, it probably...
Forum: Cast Boolits
Ok, interesting load. Now I have to ask: what are they being shot in?
I am assuming you probably know this, but felt like it might be worth mentioning for the less experienced members of the...
I have to agree with getting a 6 cavity mold. I have both 2 and 4 cav molds, and find myself wishing for a 6 cav at times. Still, its hard to beat NOE and MiHec molds.
As for TLing a non-TL...
Forum: Cast Boolits
Hi Jonesiv,
Welcome to the forum. As you've already noticed, there is a lot of valuable information to be had, and if you don't see the answers you are looking for, feel free to ask.
I will...
Now you're just trying to get me into trouble. :mrgreen: Actually, the XD-s that I want to feed is still new and unfired. I've been trying to solve that problem but either the schedule or the...
Oh no. Now I may have to pony up the cash for one of Miha's amazing molds. I'll just tell myself that its a choice between this and spending the money on j-words. After all, I have to feed the...
Neither - that's the XD-s in .45 ACP. This is Springfields 3.3" single stack version. Round count is a bit limited (5+1 with standard mags, 7+1 with the extended mags), but highly concealable.
Forum: Cast Boolits
Cedar Rapids., IA
Thanks for the suggestions. My wrinkled bullets are most likely from the early part of the session before the mold was fully up to temperature. I certainly noted that once I...
Forum: Cast Boolits
Hi all,
Spent some time this afternoon casting my 165gr 452 Lee round nosed bullets with decent results:
http://i1137.photobucket.com/albums/n502/XSive_speed/2012-10-14145128_zpsa2912a4b.jpg
...
Ok, I'm looking at the bottom of the slide. I see a ramp on the back leading edge of what I assume is the striker. That looks like it would hold down the cartridges in the magazine. If there is...
Also good information. The XD-s is the somewhat new (out for 6 months or so) 45 single stack subcompact.
I was hoping that the problem with feeding H&G 68s in the regular XDs had something to...
Hmm.. Good information on the H&G 68. Guess I will need to see if I can trade for a few to try before I invest in the mold.
Thanks for the suggestions.
jld_in_IA
Hi all,
I'm trying to find a good candidate to feed my 1911 and XD-s at the range. Unfortuantely the only .45 mold I currently have is a two banger Lee 165 gr RN.
Realizing that every gun...
Forum: Reloading Equipment
Hi all,
My old Lyman 45 lubrisizer may be about shot now, but I am hoping for some suggestions that may allow it to soldier on for a few more years. The base casting had a small crack, which then...
Forum: Leverguns
Ok, I'm currious. Is 10 gr accurate? I'm asking because I don't see anything on Alliant's site for using Unique in 45-70, so I don't have any info to sanity check this against. It just sounds...
Forum: Leverguns
That's exactly what I'm thinking - Micro groove should not be a problem. I just don't have any experience with it yet, so thought I would see if there was additional wisdom to be had.
So the...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |