Wolfdog91
I use the Lee 55gr with a gas check, powdercoated and sized to .225 23.0 gr. Of win 748 with 2.100 col. Thanks to Elvis ammo it works for me.
It groups very well.
Good luck Rickshaw
Type: Posts; User: Rickshaw
Forum: Cast Boolits
Wolfdog91
I use the Lee 55gr with a gas check, powdercoated and sized to .225 23.0 gr. Of win 748 with 2.100 col. Thanks to Elvis ammo it works for me.
It groups very well.
Good luck Rickshaw
Forum: CB Loads / Military Rifles
Any further progress? I'm interested in this pursuit.
Thanks,
Rick
Forum: Cast Boolits
Perfect timing! I'm casting Lee .225 55gr. PCing and gcing I'm looking to go 300 yards.
I would prefer to use H335 but, I'm asking for some guidance here......for my AR 16'' 1-7
Thanks, Rick
Forum: Casting Equipment
I cast in my basement with no to little ventilation. Clean lead
BUT I SMELT IN MY GARAGE WITH PLENTY OF VENTILATION!!!!
I will sweep the area clean rather than vacuum, but I mist the
area to keep...
I use half pint mason jars......I label the lid with a sharpie.....
Forum: Case Forming / Re-forming
Looks like Mike will get my hard earned dollars.
After further review and since the Annealeez comes with the torch and hose........Annealeez will be the one!!!!!!
Forum: Cast Boolits
Are you just pc'ing or are you using gas checks also. I'm very interested
in this, as I have a 1/7 twist and I'm considering cast and pc only.
I would prefer to just powdercoat, if possible. Hoping for more guys to chime in. In my original post I was referring to aluminum moulds. I understand brass moulds transfer heat more slowly.
It seems, from what I've read that casting for smaller calibers can be problematic.....
keeping mould temp up for a number of reasons, aluminum moulds at the top of the list.....what if you were to...
Forum: Cast Boolits
I want to cast for my .223 but I want a heavier pill than 55 gr.
Who makes a mold to solve my quandry?
I already cast and powdercoat for 45acp with great success. Already ran the search but it...
Forum: Casting Equipment
I started by adding the sprues back to the pot at every cast, what I found was the contoller kept compensating for the change in pot temp. The next time I cast, I collected 20 sprues at a time then...
Forum: Casting Equipment
I have been casting and learning.........started casting with a coleman stove and cast iron skillet. Then I made my own bottom pour from a 30lb. propane tank. The inconsistencies that I had were...
Moonie..... I'll explain.....
the load recipe I obtained (from a reputable source) called for no reduction in charge, no work up or max.....just that charge.....his SWC and mine evidently were not...
Thanks for confirming my gut feeling... I'm going to pull them and start over.
I appreciate all your advice....Rick
I've searched 30 pages...looking for load information and for the life of me the search is not my friend....been casting and pcing for a couple of years, thanks to you folks.
got a new Lee 452 200...
Forum: Coatings and Alternatives
I'm new to this........but, I tried the Harbor Freight red dry tumble and it worked for me. I baked in my little cheapo toaster oven that I use for Kydex but I noticed the oven just gets a little...
Forum: Cast Boolits
Just a little late responding to this.....A little outside of the box thinking here.
Perhaps that brass is too soft.....like it got caught in a fire.
Just my .02 worth
Forum: Classics & Stickies
What about using layers of fabric? Old T-shirts, Flannel, Denim......layer upon layer, sort of like layers of fiberglass. You could compress the fabric between two sheets of plywood or your choice....
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |