RotoMetals2Titan ReloadingWidenersLoad Data
Lee PrecisionMidSouth Shooters SupplyReloading EverythingInline Fabrication
Repackbox

Search:

Type: Posts; User: huntnman

Page 1 of 9 1 2 3 4
Results 1 to 25 of 220

Search: Search took 0.00 seconds.

  1. Please add me to the list 1 BRASS three cavity...

    Please add me to the list 1 BRASS three cavity plane base hp mold huntnman at swbell dot net.
  2. Replies
    9
    Views
    1,204

    Would like to follow thread, have interest.

    Would like to follow thread, have interest.
  3. Replies
    17
    Views
    2,636

    Will take 380,30/06,44, Dillon dies. ...

    Will take 380,30/06,44, Dillon dies. Greg<huntnman
  4. Replies
    17
    Views
    2,636

    PM sent on remaining Dillon dies.

    PM sent on remaining Dillon dies.
  5. drop post

    drop post
  6. drop post

    drop post
  7. Replies
    22
    Views
    2,284

    WTS If not too late i could use a blue five pack also.

    If not too late i could use a blue five pack also.
  8. Replies
    16
    Views
    3,106

    VS I'll take the last three. Greg

    I'll take the last three. Greg<huntnman
  9. It looks like your regulater is adjustable lower...

    It looks like your regulater is adjustable lower the preshure. Air in take is adjustable too, losen the two screws turn silver disk to adjust. If flame doesent respond to lowering or raising...
  10. Replies
    25
    Views
    3,736

    Yes it could. Reduced loads could reduce pressher...

    Yes it could. Reduced loads could reduce pressher and velosity. If there isnt enough velosity the projectile, may not stabilize, rate of twist and weight of projectile pending.
  11. One of the first things i did. Looked to make...

    One of the first things i did. Looked to make sure if I could see any damge to surfaces. to my inexperianced eyes all looked good, but I did have an small object (small roll of electrical tape) fall...
  12. + My scale is like many have previously stated...

    + My scale is like many have previously stated giving different readings of the same charge. the same three grain charge may read 2.8 - 3.2 grains. I now do not trust it. Can not get zero to be...
  13. I have one I would love to have repaired.

    I have one I would love to have repaired.
  14. Replies
    12
    Views
    1,650

    Sizing sink I believe would be very hard to do....

    Sizing sink I believe would be very hard to do. Would love to see it done. I cant cut sink wheelweight with a large nine inch side cutter.
    YMMV Greg<huntnman
  15. Forum: Cast Boolits

    I'm suspicious that the mold is not mating...

    I'm suspicious that the mold is not mating correctly the parting lines don't look correct.
  16. Replies
    2
    Views
    301

    Willowbend ^^^ A+++ Supper guy to deal with....

    Willowbend ^^^ A+++ Supper guy to deal with. 8/23/21 Greg<huntnman
  17. Replies
    2
    Views
    808

    will take per our PM. PM on way Greg,huntnman

    will take per our PM. PM on way Greg,huntnman
  18. Replies
    46
    Views
    14,368

    Forum: Helping Hands

    Picked up mine I found it on the front porch...

    Picked up mine I found it on the front porch today. Happy Happy Happy. I was worried I might of been the victim of the lost and stolen delivery system. Yes I maybe a pessimist. Anything good can turn...
  19. Replies
    46
    Views
    14,368

    Forum: Helping Hands

    I could use that greenish rainbow on my RCBS...

    I could use that greenish rainbow on my RCBS supreme press. thanks for the offer.
  20. Replies
    61
    Views
    6,288

    Forum: Cast Boolits

    What I see is your mold halves are not in...

    What I see is your mold halves are not in alignment. .003 off in your drawing. Bottom shifted to the right top shifted to the left. The parting line on the boolit shows one side of drive band sized...
  21. Replies
    21
    Views
    2,011

    Forum: Cast Boolits

    Washer on top of sprue plate concave up towards...

    Washer on top of sprue plate concave up towards head of the screw.
    Screw head
    washer bubble up
    ...
  22. 1 Depends on the heat output (BTU) of your...

    1 Depends on the heat output (BTU) of your burner., probably .
    A wind screen may help, you need to concentrate heat to the mass, stand, pot and contents. The first 1" ALWAYS takes the longest.
    ...
  23. Sounds like your burner might not produce enough...

    Sounds like your burner might not produce enough heat. When melting lead the first 1" always takes longer. You have to get every thing up to melt temp. Skim and flux once all is melted. There is a...
  24. Replies
    25
    Views
    3,639

    Gorilla Glue works for me. If they do come lose...

    Gorilla Glue works for me. If they do come lose its a quick fix. I have a set of handles for most of my regular use molds. the ones I have glued on have held up well.
  25. Replies
    3
    Views
    518

    Ill take these pm on its way. slow typing

    Ill take these pm on its way. slow typing
Results 1 to 25 of 220
Page 1 of 9 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check