Thank you all. I will send him a link to this thread.
Jeff
Type: Posts; User: Jeff R
Forum: Our Town
Thank you all. I will send him a link to this thread.
Jeff
Forum: Our Town
Hi,
My pal in Michigan just won a 6.5 Creedmore rifle at a UP Whitetails banquet. He is shopping for components, and has found 6.5 Creedmore brass available with large or small primer pockets. He...
Forum: Cast Boolits
313199
I cleaned out years of crud from these dies.
Jeff
Rocketing towards 200 posts!
Forum: Gunsmithing Tips & Tricks
What kind of alcohol would you use to dilute the dye?
Forum: Our Town
I have a DR stump grinder. It works great for what I would call homeowner use. If you were trying to make a living using it, you would get something bigger on day two. It takes time but it gets...
Forum: Our Town
I have bought 5 guns off GB. All shipped to my local FFL guy. 100% satisfaction.
Shoved to the back of a cupboard, I found an 8 lb. jug of 2400 that I didn't know was there. I was so happy
Forum: Shot Loads For Pistols
The blue capsules were an estate sale find. I had bought the bag of shot years ago to make some homemade scuba diving weights.
Forum: Shot Loads For Pistols
These were right out of the Speer No. 11 Manual. By brother asked me to do some pest control in a barn that he uses as a wedding venue. I could fit about 91 gr. of 7 1/2 shot into the capsules. 5.0...
Forum: Special Projects
I never set these crescent butt plates down, so they won't get scratched. I made a few trips to Tandy Leather, and made these butt plate covers. Four more to go.
277010
277011
277012
Forum: Cast Boolits
273603
I poured up a pile of Lee 309-113 Soup Can Boolits
270826
Hi,
The factory trigger pull on this GP100 was quite heavy. I bought this new spring kit, and installed the 9 lb. spring. I get the occasional failure to fire, due to a light firing pin...
270825
I got this in a box of free stuff. It might appear that is is not closed all the way, but it is. The contact point on the left is a round dome instead of a flat cylinder. It is closed,...
Forum: Our Town
My LP supplier has a propane leak sniffer. It's like a mini metal detector, but with a short sensor probe instead of the long tube that holds the sensor. It starts buzzing when it detects gas, and...
Forum: Factory Rifles
There is a DPMS AR10 (in .308) on the used rack at the LGS. It has a scope mounted and has one magazine.
The price seems reasonable. To those who know, have these DPMS rifles garnered any...
Forum: Single Shot Guns
Hi,
I would slip the whole box into a custom Foodsaver bag and vacumn seal the whole thing.
Jeff
Forum: Testing Area
252106
These stars are in a post I recently made. I only got one out of five. Is getting stars a good thing or a bad thing? Am I walking the plank?
Thanks in advance.
Jeff
Forum: Cast Boolits
I like my Lee Hardness Tester. When I finish a casting session and have reloaded the pot, I make a puck of the contents and then take it down to the Bunker and do a hardness test on it.
247146
...
Forum: Our Town
My Dad was 21 years old when the draft started, before WW2. He was the first man drafted in Chisago County. He ended up in the Army, in the 164th Infantry Regiment, which was part of the Red Bull...
Forum: Cast Boolits
I would recommend coming up with a good record keeping system, from the very beginning. I would make notes about each load you shoot, and keep them for each firearm.
Forum: Cast Boolits
The snow has finally melted. It seemed like a long winter. I had to get out a couple times. The pile of snow makes a good boolit trap.
239931 239932
239933 239934
239935 239939
I got my...
Forum: Leverguns
Wayne,
Thanks for pointing this out. I didn't realize the the boolits were so soft. I will shoot a few and see how it goes. I'll probably end up using less of a charge.
Jeff
Forum: Leverguns
The barrel slugged at .3565". I shot 15 358-429's that were sized at .358. They worked fine, no leading.
Jeff
Forum: Leverguns
I know that this topic has been discussed before. For you guys with experience in this matter, are these boolits too pointy to use in a tubular magazine? The rifle is a 35 Remington, and the charge...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |