The manufacturer of that black spray goo told me acetone. I was used to old trusty rusty iron molds, and the only way to drop respectable boolits was with coating the cavities with goo. I messed up...
Type: Posts; User: Casting_40S&W
The manufacturer of that black spray goo told me acetone. I was used to old trusty rusty iron molds, and the only way to drop respectable boolits was with coating the cavities with goo. I messed up...
Forum: Casting Equipment
Both of my 2's and 4's and the one 19 that came with the press have the groove.
Forum: Casting Equipment
Titan has the X-press Shellplates in stock, I ordered one extra of #2 and #4 for the same reason..
Forum: Cast Boolits
I use the new Lee Ultimate lock rings, the split clamp design and the free die wrench sold me. The gold plating really classes up my old rockchucker.
...
Forum: Reloading Equipment
Saw it on the LEE Reloading & Casting Equipment Group page...
247432
They do make em, just not catalogued. I ordered a bunch of six cavity round ball molds from Track of The Wolf.
They have all of the popular sizes and are nice to deal with.
I had the same thing happen and talked to Lee. They said this is a brand new product and has an engineering feature that can cause this problem. It is the rubber up stop on the lever. They put it...
Forum: Reloading Equipment
Screw a sheet metal screw into the lock pin if it is stuck down. The screw can be used to pull the button up.
Forum: Casting Equipment
Straight from the horses mouth.
http://leeprecision.com/satisfaction-guaranteed.html
All my newer Lee DC molds use a Left Hand thread. When you open the sprue it is always tightening the shouldered bolt. IF you have so much friction that its is wanting to loosen when closing the...
Forum: Reloading Equipment
Your powder measure must look just like mine then. When you stare down the barrel of where the hopper goes in, with the small drum, half the opening is exposed.
Forum: Reloading Equipment
"dragon813gt"
This new measure sure is the cats meow, here is what I found out.
I noticed the leakage on your measure is on top of the slider. This could only happen if the powder is working...
Forum: Reloading Equipment
$32.61 for Lee Set.
It pays to shop around. Found this set at a Cast Boolits sponsors website.
http://www.titanreloading.com/lee-22-tcm-2-die-set?filter_name=90803
Tap in/reinstall with a 3/16" punch, and stake on either side with a nail or center-punch to permanently secure, as tward noted.
Mold release spray reduces the "as-cast" diameter of the bullet, especially on TL bullets. Wood match is the best.
Definitely galling under the sprue pivot. Takes about .010" of clearance to flash/fin..
Sorry to hear about your misfortune. Sticking can be caused by the cavities not being centered in the two mold half's.
Forum: Cast Boolits
Holding the mold over the pot, to drop reject bullets will cause these sort of mystery spots to appear. Drop all bullet on a soft cloth or bucket of water, away from your melter setup.
Forum: Reloading Equipment
Installing the press lever incorrectly may have caused this failure. The lever must pass through the lever clamp and engage on both sides of the semi-circular cut of the press toggles (gold color...
Forum: Cast Boolits
No change, is good change.
http://leeprecision.com/satisfaction-guaranteed.html
"slight deformations, some w/wrinkles on heels, some w/gaps in the driving bands, some w/deformed domes"
Symptoms of Zinc contamination
Forum: Reloading Equipment
Went to Lee FAQ
http://leeprecision.net/support/images/PrimerRestrictions.pdf
Explicitly says, no Federal
I do not believe there is a blast shield for the P1k
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |