Search:

I was a day or two late, too. (near panic) Wrote Miha and got an invoice. Perfect! He always makes some extra.

I wish there was more about Kent Lomont and his shooting somewhere. I have tried to find out but guess there is not too much material available. Someone should write his biography about guns and...

DukeInFlorida, that sounds perfect. Especially your gas check system.

I use Carnuba Red too, with some ad hoc external heater. Great lube.

Can I ask, have you measured your 6 1/2" S&W cylinder...

DukeInFlorida, I don't know about the seating die problem either. I was referring to msg #13 and #14 in the link. The boolit must be sized under the cylinder throat diameter in order to fit the...

Is this the same mold? It won’t chamber, the nose radius was not steep enough, nor a bore ride.
http://castboolits.gunloads.com/showthread.php?179455-MP-502-600-Results
Nose length was .650 if it...

Please, count me in for (1) two cavity mold, gas checked, all pins - reader454424 at gmail dot com

I have the PB version already and want the GC too for max. velocity.

It was something like 400...

I would like to buy one. Looks great. I have a punch, though.

I would like to buy a 3 cavity Cramer HP.
reader452 at gmail dot com

I got my .480 SRH for cheap. Mounted 30 mm Ultradot. I ordered a custom 405 gr mold with .500 long nose from Mountain Molds. At least my SRH can chamber it. A bore riding design. I sort of followed...

I use WineBottler to run QuickLoad in Mac. "WineBottler packages Windows-based programs snugly into Mac app-bundles."

It works and it's free.

35W, thanks for the clarification! I only wrote a disclaimer, I cannot estimate it or have time to test. 44man experience was about .44 mag anyway with higher pressures. Could be a combination of...

Some time ago I bought 2 lbs of old Hodgdon H4227 for cheap. I have shot one lb already.

Linebaugh has some "Ruger-only" .45 Colt data:...

Yes, the reasoning for these regulations is a joke. I live outside US too, and for example I could not buy scope rings for my Ruger SRH. After a long search, I found them then from other country. A...

Sorry, I did not notice your reply. Forgot to subscribe this thread. My gun had a defective barrel and very large cylinder side play. The barrel had machining marks through the full length.

A gas...

Thanks. I found some problems with the gun. I have to fix them first.

I cast Alley Cleaner 473 gr as solid, 400 gr large HP pin. I size to .500 and shoot 1400-1500 fps. The alloy is WW equivalent and the solid version water dropped. HPs were air cooled. I get...

I size MP502-600 to .500 and it doesn't chamber. Is this the same issue? My JR500 has .4995 throats or close. The .500 dia. sizing die touches up to .250 of the front section or front band...

I would be interested in 250. reader452 at gmail dot com

I would like one .462" mold with extra blank pins.
reader452 at gmail dot com
Thank you!

Thanks for the info.

The last picture is great. It shows the boolit in every angle. :D

When I look the catalog, #1101/#501 looks different than the cast examples here in the forum.

42412

Below is a Ballisti-Cast #1101 photo by GLL.

42413

The catalog picture with thick...

Probably it is. The projectile would remain inside the cavitation bubble. The sharp edge seems important.

Here are few examples:
http://www.grosswildjagd.de/penetrat.htm...

Here's the rest of the story. MacPherson saw this anomaly first with a 10.08mm SWC. Penetration went suddenly trough the gelatin block at 1065 fps, when it should have been approximately a third...

I bought the MacPherson's Bullet Penetration book. In fact by jwp475's recommendation here. Thanks!

MacPherson describes anomalous data with SWC bullets p. 186-193. The penetration suddenly...

I would like to buy 2 lights and 2 packs of batteries (8 pcs). Shipping to Finland, please. I think intl. small flat rate box should be $17.