ballistic products had 24ga. brass shells when i needed them - try emailing them -
Type: Posts; User: schutzen-jager
Forum: Shot Guns
ballistic products had 24ga. brass shells when i needed them - try emailing them -
Forum: Cast Boolits
jmho - 4.5 to 5.0 grains of red dot under a 230 gr. hard cast bullet will do anything that the other powders listed + using 1/2 the amount of powder -
Forum: Black Powder Cartridge
not all actions are not open at top + on many the only opening is a small ejection port on side -
Forum: Black Powder Cartridge
[ I'd be more inclined to fab up a bore guide for the muzzle end. ]
cleaning from muzzle it almost impossible to keep debris out of action, no matter how carefully you try -
Forum: Gunsmithing Tips & Tricks
depressed the plunger on edge of work bench, held knurled part with padded jaw pliers, + pulled back on grip frame - tried the .0004 feeler gauge as suggested but not enough space between pin +...
Forum: Gunsmithing Tips & Tricks
Schiff C gun service in in Murray, UT.used to do them - also i think Connecticut Shotgun manufacturing does them =-
Forum: Gunsmithing Tips & Tricks
received the replacement pin from NAA a few minutes ago, now functioning like new - could find no visible problem with old one - i do not know what was causing detent ball to not retract - pin assy....
iirc trailboss was sold in smaller then 1 lb. containers - believe the containers to be 9 oz. + 2lbs. -_
Forum: Our Town
58 years ago when i married my wife she was a red head, now it is all grayish -
this is the third one i had - sold the other two atmy collectors association meeting - the other two were filled - this one is half empty + has had no takers -
Forum: Gunsmithing Tips & Tricks
if you can find a copy of the Home Gunsmithing Digest by Tommy L. Bish starting on page 174 there are 5 ages detailing how to install the kits that are available + starting on page 180 there are six...
iirc the Winchester white box ammo has only been sold in past 30 years - definitely not 1923 -
nice - Straw hat have you tried to obtain any Tyler t grips lately ? -
Forum: Gunsmithing Tips & Tricks
again thanks for the replies - heard from NAA + they are shipping a replacement assembly - will post when it arrives -
Forum: Gunsmithing Tips & Tricks
thanks for the reply the plunger + spring are functioning properly, it seems that detent ball is not retracting into the recess - the parts list that came with it shows the cyl. pin only available as...
Forum: Black Powder Cartridge
never had any centerfires with ringed barrels, but several .22 rimfires + had no safety issues +accuracy was not effected -
Forum: Gunsmithing Tips & Tricks
thanks for the reply, spring action is functioning properly -
Forum: Gunsmithing Tips & Tricks
thanks for the reply - i already tried tried that , but no wear is visable in barrel recess or on dent ball - seems to be that when plunger is depressed dent ball does not fall into it's recess -...
Forum: Gunsmithing Tips & Tricks
now UPS + FEDX will no longer accept pistol returns from non FFL'S + USPS will not accept pistol shipments from no ffl's like they do with long arms - like i stated the NAA shipping policy is very...
Forum: Gunsmithing Tips & Tricks
like i stated the shipping charges for their warranty returns both ways is much more than i paid for the pistol when purchased new - terms are clearly listed on the web site -
Forum: Our Town
i do not know the answer but most of the sealed beam boxes used to have candle power listed on the boxes - try looking on internet - why not use LED conversion ?
...
Forum: Factory Rifles
iirc - correctly Ballistol is all synthetic + does not have any petroleum ingredients - + most mineral oil is a petroleum distillate -
Forum: Gunsmithing Tips & Tricks
thanks all - tried all of suggestions about cleaning + am aware of hammer position as in the original instruction sheet - awaiting call back from email to NAA + aware of the life time warranty, but...
Forum: Gunsmithing Tips & Tricks
decades old + carried much, shot little - function fired 5 rounds every 3 months + cleaned - now when trying to remove cyl. rod it does not come out easily when latch is depressed - detent ball seems...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |