I’d like;
4- 30-06 all Rem head stamp 100 pieces $23.00
33- 7.5X54 all PPU 40 pieces $16.00
35- .35 Rem 9 pieces WW Super and 6 pieces Rem total 15 pieces $4.50
45- 30-30 32 pieces PPU, 14 GFL,...
Type: Posts; User: huntj3
Forum: Completed Deals
I’d like;
4- 30-06 all Rem head stamp 100 pieces $23.00
33- 7.5X54 all PPU 40 pieces $16.00
35- .35 Rem 9 pieces WW Super and 6 pieces Rem total 15 pieces $4.50
45- 30-30 32 pieces PPU, 14 GFL,...
Forum: Completed Deals
I would like the Beaumont and 11.66. Pm inbound.
Forum: Completed Deals
I’ll take #3 if available. 12 gauge 2-3/4” looks all there and nice. $50
Forum: Case Forming / Re-forming
Great information. Good to know more options work since 35 Rem is getting hard to find.
Forum: Case Forming / Re-forming
Also another reason to buy one in 303B is for 30-40 Krag with oversized boolits. A 1-2mm washer around the base above shell holder and you can neck size the Krag brass to .310-312 if so needed.
Forum: Case Forming / Re-forming
The nice thing about the Lee collet neck sizers is the amount of tension you want is controllable by how far in you screw the die. I use my collet sizer to about .314-.315 for .316 boolits. For extra...
Forum: Completed Deals
I will take;
Box O- .303 Brit 377 pieces mixed head stamp $76.00
#37- 30-06 mixed head stamp commercial de primed 21 pieces $3.15
Pm inbound
Forum: Case Forming / Re-forming
7-30 waters might be the best intermediate die for the application. 7mm-08 could also be found easy.
Forum: Case Forming / Re-forming
Nothing will replace the easy use of the 43 Spanish die, but you could look into what dies you already have. I had used several dies(8mm Lebel, 45-70, 45 colt) to neck 50-110 to 43 werndl before...
Forum: Case Forming / Re-forming
The Redding 300 blk form and trim die is how I cut open live 5.56 blanks. Cheap fine tooth saw from Amazon, file the burr on the die, then dump the powder out. I used to use a cheap tubing cutter and...
Forum: Case Forming / Re-forming
I have not tried it, maybe someone can vouch. It looks like 6.5 & 7.35 carcano or 6.5x54 brass could be easily converted? Already has similar rim and base diameter.
Forum: Completed Deals
How many cavities on the 325365 of lot 3?
Forum: CB Loads / Military Rifles
Unless you’re absolutely set on historically accurate OAL, I remember my kropatschek having a cartridge interrupter/holder to keep the rims in place. If my memory serves, I just seated the boolit a...
Forum: Case Forming / Re-forming
I also partially neck size only with a carbide lee 45 colt die.
Forum: Case Forming / Re-forming
Lyman 446110 mould as cast (about .447/448) for my standard 67/77 infantry rifle and the same mould sized to .440/441 for my 67/77 jaegar rifle with tighter bore. I also use the Lyman 439186 mould as...
Forum: Case Forming / Re-forming
I find it easiest to neck down 50-110 Winchester. Before I had correct dies, I used a Lebel die to form cone, then into 45-70 to just below proper shoulder, then neck sized 45 colt. The shoulders...
Forum: Completed Deals
Hello,
I’d like the following please. Pm inbound.
13)30-40 Krag 137 pieces $34.25
14) 30-40 Krag 17 pieces not clean $4.08
15) 7.62X54R 74 pieces $17.76
16) 8MM Mauser 229 pieces $41.22...
Forum: Case Forming / Re-forming
Kshooter,
You should be perfect on those measurements to bell the case and load up! You could try tumble lube or dip lubing the boolits. The heeled design throws the Lyman and Rcbs sizer options...
Forum: Case Forming / Re-forming
I make 11x59r Gras from 50-110 brass and have the same issue of correct body but small rim(head spacing from shoulder). I don’t have access to a lathe, but have thought about paying someone to turn a...
Forum: Case Forming / Re-forming
Correct, about the .321. Dies are designed to size lower diameter then open up the neck with the exp button.
Perhaps it’s a tight tolerance die. Even if other 32 spl dies size to similar diameter...
Forum: Case Forming / Re-forming
Disclaimer; none have been checked in chamber or case gauge
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |