That post is totally useless as the links listed in the initial post no longer work.
Type: Posts; User: ulav8r
Forum: Gas Checks
That post is totally useless as the links listed in the initial post no longer work.
Forum: Our Town
Daughter just ordered a Lazyboy chair. $500 cheaper in Tulsa than NW Arkansas.
Forum: Gunsmithing Tips & Tricks
At least you know where you can source the replacement for the pin that will now be loose in the base. �� Edit: the smiley I picked did not display properly.
Forum: Factory & Surplus Powder
At the prices it is bringing, someone will want it even though it has been opened. I would not have it even it was unopened and priced under $40 total.
Forum: Reloading Equipment
A dimmer would allow for full heat til the lube gets to desired temp, then reduce wattage to maintain temp. Would be more user friendly for long lubing sessions and might require a lot of trial and...
Forum: Muzzleloading.
Dad had a neighbor\friend who told of us of someone who shot some dynamite that was sweating. It exploded, would not have been a big deal but they had placed it against as bluff that directed the...
Forum: Shot Guns
The shape of the stock will not affect the recoil, but it can greatly affect the PERCIEVED recoil. A badly shaped stock will affect the muzzle rise and can cause the comb to hit the cheek harder so...
Forum: Shot Guns
Physics says this is the correct answer.
Besk, the enlarged section covers your statement.
Forum: Our Town
I've seen dozens of dead skunks on the road, starting 3-4 weeks ago.
Forum: Single Shot Guns
Just now watched your video, that barrel is scrap.
Chop it back to a 3" stub and put a good barrel into it. The barrel could be turned to a slip fit and attached with Loctite stud lock, epoxy, or...
Forum: Shot Guns
I'll be a little different and suggest 9.3x72R or a larger bore with the same brass necked up. It is a long case with a nice rim.
Forum: Leverguns
Removing dents with steam works best if there is no finish. If you don't remove the finish result likely will not be reliable, either the finish will be damaged or the dent may remain.
Forum: Gunsmithing Tips & Tricks
You would have better luck finding diatomaceous earth.
Forum: Lead and Lead Alloys
If pure, it should be east to scratch with a fingernail.
Forum: Cookin' Recipe's
the If it is tough, the way mom used to cook venison would work. She cut the steaks thin, 3/8 inch at most. Salt lightly, roll in flour, then into a hot skillet with a touch of bacon grease. When...
Forum: Case Forming / Re-forming
I do not shoot tarnished brass. It tastes bad, is hard to chew and does not satisfy my hunger.
Forum: Our Town
Highly recommend 1632 by Eric Flint. Currently have just over 3900 books on Amazon, about 7500 my computer, and a few on my phone. Have quite a few print but they are too hard to keep handy and at...
Forum: Special Projects
If you use screws to adjust the muzzle, keep them as close to the cut point as possible. The further the cut is from the screws the more possibility there will be a change in impact point after the...
Forum: Single Shot Guns
Would you fire each case indexed several times to determine the best orientation to mark permanently for each one so that you could fire several to get a group?
Forum: Gunsmithing Tips & Tricks
No "gunsmithing" tools should be needed to fit the larger threaded barrel except for an action wrench and barrel vise. You will need a depth micrometer and either a GO chamber gauge OR a few...
Forum: Case Forming / Re-forming
I would like to try a 32-20 with tp black powder and home made primers per the two threads in the muzzle loader section. It would be a little more conveient than a 32 muzzle loader with the same...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |