Search:

N320

So that's where all of the SP's went .... dannyd's place.

Powder Valley has it currently at $24.79 per bag of 50. If anyone is still looking. When Midway ran out, it showed up there a week later and I grabbed some.

I later found Nitro-100 NF at BlueCollarReloading. He's way under market for that at $21.70 ... but he's down to 3 at this point.

I hit it hard today across a few sites: N550, N555, N560, N568,...

He's even got some old HS-7. 40#'s of it.

At MidSouth I got 3lbs (4 - 12oz bottles) of Nitro 100 and 1lb of Reloder-16 ... which I paid too much for ... with a free shipping code.

Also hit Brownell's for 1lb of BE-86 (never tried it) and...

N110 maybe.

I've only got one can of BE-86 that I've still not opened. My understanding is that it is basically Power Pistol with a flash suppressant added. Someone may come along an correct me.

I went there to check it out a few minutes after the email popped into my inbox. There were none in stock. Who send a promotional email for something they don't actually have.

Just in case the OP missed it, I'll say it again. Sportsman's Warehouse in Lady Lake, FL which is probably an hour South of Gainesville. RCBS single stage presses, Hornady progressives, RCBS dies...

I don't like One Shot because I had a can seal fail and leak schmoo all over my shelf. I've moved on to BrassJuice in the spritz bottle.

Sportsman's Warehouse in Lady Lake. Go to the sportsmans.com site and set your store to Lady Lake. You can see their reloading inventory. There's a limit of 200 primers a day currently. They do...

I will put two spritzes of Brass Juice on 100 new Starline 45 Colt cases and toss them for a bit in a Tupperware bowl before running them through the progressive even with the carbide dies.

Yeah, it was rock hard. I hit it with an alumina stone in the Dremel. I did both the top and bottom. My press binds occasionally because the primer seater catches the bottom edge of the primer...

There's one up on fleabay right now with a $500 stating bid. It has the auto-index and two extra die plates but still uses the APS primers. No takers so far.

Oh, now I get it. I couldn't figure out exactly what it was doing. Great idea. I was focused on your wire retainer for the primer tube mount.

BTW, what tool did you use to put the chamfer on...

I just got off the phone with RCBS and they are sending me a spare shoulder bolt and a slow twist index rod for my Ammomaster. Apparently, they came out with the rod many years ago to reduce the...

Could it also be done from the bottom I wonder? That retaining ring on the bottom seems more accessible to me. The one holding the nylon bushing looks like an hours work with a fine pick or...

Amen to that. That rod flopping around in that slot on the "case detector" was pretty Rube Goldberg-ish.



No love for the thumb screws. :(



What are you using here? Some super light...

The Ammomaster had 5 stations before it was fashionable. :)

There should be an AmmomasterAuto sub-section on one of these boards where we can all commiserate and share hacks.

And yet, here I sit jealously eyeing your spare 5-station top plate. Knowing that I have a spare set of legs / risers and I could have it setup and standing aside in another caliber.

I was thinking of trying to 3D print a replacement part for that white piece that holds the tube but modified to accept an outer tube. PLA+ filament seems pretty tough these days and might hold up...

As far as I recall, it was popular to replace the handle on the Ammomaster with one from the older series of Rock Chucker (1 and 2) to reduce the stroke. So popular, RCBS ran out of them.

Below...