Hello to all.
Thanks to all for the replies.
The Corbin products are so hard to find in Italy. They are non imported and the buy in USA is so expensive.
Thanks again.
Ciao
Nino
Type: Posts; User: iwottopq
Forum: Swaging
Hello to all.
Thanks to all for the replies.
The Corbin products are so hard to find in Italy. They are non imported and the buy in USA is so expensive.
Thanks again.
Ciao
Nino
Forum: Swaging
Hello to all.
But...but...what brass to form for .308 caliber? Beyond that 5,7x28 of course...
Thanks
Ciao
Nino
Hello to all.
This is my last purchase...a Cz 527 in 6.5 Grendel.
Forum: Single Shot Guns
Hello Marlinman93.
Thanks for your help, the video is very usefull. I was actually looking for the value of each mark on the diopter. the trajectory calculation will come later, as soon as a...
Forum: Single Shot Guns
Hello to all.
Hello Sgt H and thanks for the reply.
This in the pics is the tang that I use. I do not know how calculare with it.
I noemally shoot with optics.
Thanks again
Ciao
Nino
Forum: Single Shot Guns
Hello9 to all.
I have a Pesersoli Sharps in .45-70 caliber and is is zeroed at 100 meters.
Now I have the possobiloity to shoot at 675 meters but...but...how I ca do to st the diopter for this new...
Forum: Gunsmithing Tips & Tricks
Good morning. The bolt seems to close completely and well. At the moment in which the firing pin is struck, empty, it clicks up by about 1 millimeter. All the cases I have used have been resized...
Forum: Gunsmithing Tips & Tricks
This is a good idea, I need to inspect the recesses in the bolt lugs. It will be a bit difficult as I don't have a borescope but I will try...
Forum: Gunsmithing Tips & Tricks
Good morning. There's no problem.
I used a lot of primers (CCI-FIOCCHI-FEDERAL) all LR. Finally I tried with the LP FIOCCHI but also these ... same result.
Forum: Gunsmithing Tips & Tricks
My English is scholastic and therefore not very good but in my post I never complained about the lack of precision which, however, is excellent with my cast boolit and load of any hunting powder. The...
Forum: Gunsmithing Tips & Tricks
I never used factory ammo on this caliber...:p:p:p
Forum: Gunsmithing Tips & Tricks
Hello to all.
I have a Remingtn 783 in .300 WM caliber. It is a great gun, shoot very well with my lead cartridges but...but...some days aga it started to not shoot. I changed the primer with LP...
Forum: Coatings and Alternatives
Hello to all.
It is a so nice method...
Thanks for condivision.
Ciao
Nino
Forum: Gas Checks
Hello to all.
I prefer before so I can pc also them...
Ciao
Nino
Forum: Swaging
Hello to all.
Hello M.A.D. and thanks for your reply. Can you give me more informations on the way to form .308 bullets from 9 m/m brass? Keep in mind that I have only a RC II press and not a...
Forum: Swaging
Hello Jim...thanks for your reply.
I thinks that the only brass usable for .308 jacket is the 5.7x28 but this is a so hard to find caliber in Italy.
Thanks.
Ciao
Nino
Forum: Swaging
Hello to all.
I am new on swaging. My experiences is limited to obtain .45-70 bullets starting fron .45 ACP cases with poor means.
Now I would like to obtain .308 bullets but from which cases?...
Forum: Reloading Equipment
Hello to all.
I use the Lee dies with satisfaction.
Ciao
Nino
Forum: Gas Checks
Hello and thanks.
How I can contact Charlie?
Ciao
Nino
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |