With hex pin support, by drilling a hole in the shaft of the motor ?
Type: Posts; User: rogerandre
Forum: 3D PRINTED RELATED ITEMS
With hex pin support, by drilling a hole in the shaft of the motor ?
Forum: 3D PRINTED RELATED ITEMS
Just a humble future enhancement request when time permits: Moving the size of the drop tube down so the number is visible when the proximity housing is in place. 325346
Forum: 3D PRINTED RELATED ITEMS
Huge thanks TylerR and GWS
Rock Hard !
Forum: 3D PRINTED RELATED ITEMS
Dear Team !
What would you say is the minimum recommended size (Amp) on the power supply when running M634JS motor ?
M634JS requires 0.3 A normal operation and approx. 1.6 A max (jams etc.). ...
Forum: 3D PRINTED RELATED ITEMS
You are truly a superstar TylerR !
What I am looking for in an optimal setup is something like Tanders 9mm_Dillon_Case_Feed_Adapter.stl but with integrated spring threads.
Now I guess I can use:...
Forum: 3D PRINTED RELATED ITEMS
Dear Team !
Would be grateful for pictures/inspiration on what adapter that you have used to connect the spring from the collator to the casefeed body on a Dillon 750.
Are you hooking up to the...
Forum: 3D PRINTED RELATED ITEMS
Hi TylerR !
Not done any changes yet. Will play around. Once again thanks !
Forum: 3D PRINTED RELATED ITEMS
Worked out fine. If I should say something it sometimes takes time for the brass to fall into the slots. Perhaps the ridges can be enhanced.
Huge thanks for all the help.
325077
325078
325079
Forum: 3D PRINTED RELATED ITEMS
GWS you are spot on as always.
I will give plate builder a shot. Will just see if TylerR have any divine feedback. Will of course share when I have a working plate. All about teamwork !
Forum: 3D PRINTED RELATED ITEMS
Dear Team!
Anyone that by chance have designed a collator plate for 6.5x55 Swedish brass base down ?
Best regards
Roger
Forum: 3D PRINTED RELATED ITEMS
Think the debris will follow the collator clockwise and end up just to the right of the mount. At least that was the case for me. (BTW love GWS sense of humor :-)).
Forum: 3D PRINTED RELATED ITEMS
Thanks alot for the exellent feedback.
TylerR, the idea of a trap (perhaps just a hose) is great. One of my other brass feeders just drops on the bench and makes a mess.
Once again thanks !
Forum: 3D PRINTED RELATED ITEMS
Dear Team!
Any plans on adding a small hole (or similar) in the main body to allow for dumping out sand and other dirt from range brass ?
Best regards
Roger
324724
Forum: 3D PRINTED RELATED ITEMS
Dear Team !
Is the Rifle_Brass_Collator_Plate_Large.stl the optimal plate for 308 Win brass ?
Best regards
Roger
Forum: 3D PRINTED RELATED ITEMS
Please post some pictures of your mirror setup. When time permits.
Forum: 3D PRINTED RELATED ITEMS
Dear Team !
Anyone that have been playing with a small camera/screen to monitor the brass/bullet level in the collator ?
Perhaps just using a small Tuya camera and stream to a phone ?
Best...
Forum: 3D PRINTED RELATED ITEMS
Dear Team,
What size of the APP_Offset_Connector_X do you recommend for 9x19 and 223 rem brass ? Neither caliber brass will pass the APP_Offset_Connector_10.stl.
Best regards
Roger
Forum: 3D PRINTED RELATED ITEMS
Ouch ……..classic RTFM scenario. My bad. Please accept my sincere appologies.
For the Lee APP accessories is it correct that APP_Spring_APP_Insert_X can be fitted directly on top of...
Forum: 3D PRINTED RELATED ITEMS
Dear Team !
I have started fiddling with the Lee APP accessories.
Firsts tests will be with 223 brass that will be decapped and swaged.
First challenge I encountered is that the ...
Forum: 3D PRINTED RELATED ITEMS
Thanks GWS,
PLA Meta is from JAYO.
The parts that i need to sand are printed in .12.
Examples of where I have a poor fit is Spring_Drop_Tube_X on top of feed dies, and APP_X_Insert_X inside...
Forum: 3D PRINTED RELATED ITEMS
Dear team !
Just me that experience differences with the tolerances based on the filament ?
PLA Plus gives close to perfect fit almost all the time, PLA Meta and some sanding is required.
With...
Forum: 3D PRINTED RELATED ITEMS
Dear Team
I am looking for Spring_Drop_Tube_11 but in the repo I can “only” find Small, Medium, Large and Extra large.
What size should I use for 223 Rem and 9x19 ?
Med vänliga hälsningar/Best...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |