Search:

I saw a Tisas 1911 clone on sale for $299. The H&G 68 200g. SWC is a popular .45 ACP boolit

It looks like a Winchester 52 A or pre-A. The barrel is most likely turned down to make a "sporter". That would also explain a new stock. The original stock would have been cut for a heavy barrel.

Differences:
With pistol cases carbide dies are almost a must have.
With lead boolits it is necessary to flare case mouth so you don't shave lead while seating boolits.
With lead pistol Boolits...

The last two cans of BC sight black did not last long. The aerosel cans gave up well before the product was used.

My guess it is some type of incline level. Like if you were installing drain gutters, sewer pipes or pipes that require draining due to process changes or temperature. Center one side and screwing...

I have had the same problems with CZ 75B Omega and Canik Rival pistols. I had the THROAT reamed to accept PC boolits. Still the problem was the bore size. I had to run a .3580 boolit to keep the...

In my experience there is no accuracy difference between bevel base and flat base. In 45 ACP you have the H&G 068 and 069. The bevel base was made to prevent lead shaving when aligning and seating...

Some people complain that their ice cream is cold.
I saw the article in AR but it is on my list to read sometime. The rifles are too ugly to read the article the first time you see the pictures.

Star

You mentioned that this is happening on the last round in the factory mag.
To test the recoil spring weight, load one round in the magazine, fire the pistol. The slide should lock back. If it does...

II RC, THE BARRELS HAVE THE STANDARD 1;16 twist. The match barrel had a tighter chamber. Its unusual that a TC don't shoot accurate.

I am thinking about building a shot maker for shotgun shot. Since my PID for my casting pot works so well I would like to use a PID on the shot maker. I would do away with the normal control knob and...

What JonB said in post 14. Most foreign 9mm pistols are chambered to shoot jacketed bullets of .355 diameter. The rifling extends to the end of the chamber which causes boolits of .356-.358" to jam...

My testing using a Ransom Rest with a S&W model 14 in .38 Special. There was no significant difference in accuracy or point of impact with PC vs. traditional lube groove bullets. The bullets were...

See my PM to you

I have experienced his problem and there is no solution except to have the barrel throated ( if that is possible). I have 2 Canik and 2 CZ pistols. There is no leade in the barrels and an oversized...

I think the answer depends on the situation. If you have kin or kids that would enjoy the guns after you are gone I would get rid of the ones you will not be using in the immediate future.. I would...

In West Virginia, you make sure you have a gun before you attend a bingo game.

I get similiar bad results when I let my lube get too hot. I use White carnuba red with an unregulated heater. If it gets too hot it squirts out the lube holes and mixes with air.

My guess it is for a Star luber size .224. The spell checking does not know what a Star luber is.

My father had one in which the batteries had swelled and stuck in the tube. I tried every solution on the internet. I tried soaking with oil, kroil and atf fluid. I tried heat and time
Drilled a...

Using a tuned .45 acp target pistol with a Ransom Rest, i came to the following conclusion.
I cast 5-600 200 g. swc. I visually sorted and culled the obvious bad ones. I then picked out what I...

There are more variables than just the mold material. Things such as bullets weight, number of cavities, user tolerance to weight of mold, solid point or hollow point design, alloy of lead, and maybe...

There is no accuracy advantage. If all your other pistol calibers are small primers then you do not need to stock or use LPP.

Over my life time I have acquired about 5 pounds of misc. allen wrenches. All are 1/4" or less You know you buy a set of scope rings and they give you an allen wrench. You buy something that needs...