Search:

6.5 stuff gone. SDB still up for grabs

3 sealed boxes Nosler 6.5 100gn solid base ballistic tip - $SOLD/ea
Partial box of 88 lapua 6.5 100gn scenar - $SOLD
Forster 6.5 Grendel micrometer seater die - $SOLD

All the 6.5 stuff for...

Would you sell just the conversion kit? I have extra tool heads.

Or if you need 40 or 44 mag conversions I have them to trade

Sent from my F5321 using Tapatalk

How many amps is needed for the first one @24vdc?

Sent from my F5321 using Tapatalk

Did some research and while no one says outright the frames are called "400 series stainless" I did find that the dylinders had to be made from 465 carpenter steel, so whatever the process was it...

Does anyone know how to re-create the Ruger Target Grey finish that was done on Super Redhawks and some other guns. From what I have found some people think it is nothing more than tumbling and...

I think that titan makes one that is 3d printed also

http://www.titanreloading.com/powder-handling-equipment/titan-micro-charge

Guess I forgot that piece of info... Its a 1911 conversion.

Looked at it closely and the cerakote is perfectly on only the comp, so either someone did one heck of a tape job or more likely it was...

Just picked up a 460 Conversion. Looks like a fun round.

Is there a better deal on brass than the ~33/100 at midway? I don't think I am ready to order 500 min from starline

Does anyhave have...

Upped the game the other night, began testing loads for the 12ga. Used some of that green brass media, stuff was horrible for cleaning anyway. Federal trash shells and some old red dot I don't trust...

I like your thinking. I have a half a thing of the green junk that doesnt work and more walnut now that I wet tumble everything. Might give me a little extra range and knockdown power (valid in this...

Cream of wheat isn't popular around here so I didn't have any laying around. From the couple times I have eaten it the powder seemed finer than grits. Also less base taste. Don't want to do salt for...

The yellow jackets I usually just trap, they are too mean and aggressive to deal with.

There are holes all over my barn, fence and porch from carpenter bees. Anyone that says paint stops them...

Didn't realize the HF presses were that cheap. I'm used to arbor presses costing several hundred, but have only looked at the nicer ones. Guess I'm running by HF, needed to pick up one of the...

We bought a foreclosure 2 years ago that sat for 5 years. As a result we have been battling wasp, carpenter bees and yellow jackets every spring and summer. Last year we armed ourselves with spray...

Kennesaw has been a very popular area with a lot of growth as Atlanta sprawls. Once you get past that prices start going down and lot sizes increase. If you want more of a small town there are a few...

Have you looked at this design: http://www.realitysurvival.com/survival-resources/free-shooting-bench-design-plans/

Cut from 1 sheet of Plywood, packs like ikea

Check in Canton, Cartersville and Rome. A short, limited traffic drive down to Kennesaw. If you are outdoors type you'll prefer those areas anyway. Jasper may be an option also depending on where...

I ended up setting up a shell holder plate for the pro1000 just for SPP. There are enough of them around me to make it worth being able to reload. It is annoying to sort after range pickup

When...

Just picked up a ruger super redhawk in 454 and looking forward to getting some rounds loaded for it. Dies are confusing me, information seems to be varied and conflicting

Some say 45LC dies will...

Very cool, and I thought custom molds required heavy machinery

Ok, now I have to have a 460 Rowland...

Are you guys building dedicated guns or swapping calibers back and forth?

Thanks. I plan to start a thread with the designs I have once they are finalized.

I run all my 9 through a BB after several failed rounds. I use all range pickup brass so some has been glocked. Once you get going its a pretty quick process.

There are 2 main issues that I have...

I am working on a 3d printable peg board holder for various dies and such. Already have the dimensions of the 3 hole version but if someone can send me the dimensions of the 4 hole one I can add that...