This one came with two different nipple sizes...
Type: Posts; User: jason280
Forum: Cast Boolits
This one came with two different nipple sizes...
Forum: Cast Boolits
https://i.imgur.com/oWByUkN.jpg
https://i.imgur.com/Mg3SAfL.jpg
https://i.imgur.com/JzlR1gi.jpg
Forum: Cast Boolits
I was able to pick it up today for $130 OTD, which I thought was a pretty good price. If its been shot, it wasn't shot much...and was definitely cleaned up properly after use. Only think I need is...
Forum: Cast Boolits
I'll see if I can find out more about it tomorrow. They're asking $150, I'm trying to get it for $125...either is a fairly decent price. I *thought* I had an extra .58 cal mold, turns out all I...
Forum: Gunsmithing Tips & Tricks
There's quite a few available on eBay...
Forum: Gunsmithing Tips & Tricks
I thought that was likely the issue. I actually pulled the spring this morning, and it was mostly flat. I manually bent it a little to give it a little more curve, and reinstalled...didn't really...
Forum: Cast Boolits
No idea on the manufacturer, just stamped "Italy" on the barrel.
Forum: Cast Boolits
Anyone familar with the generic Italian made Zouave .58 cal clones? I have a chance to pick one up in excellent condition, just not sure what one would be worth.
Also, any suggestions on a .58...
Forum: Gunsmithing Tips & Tricks
Anyone familiar with Marlin 39A lever rifles? I have one where the carrier/rocker doesn't always came up to lift the next case in position, and can't figure out exactly why. I'm assuming it just cams...
Forum: Case Forming / Re-forming
I've seen 6.5x50 Japanese brass formed from .35 Rem, could it work in reverse (not sure if OAL is the same)?
Forum: Cast Boolits
I just picked up a Ruger American in .450 Bushmaster, and trying to decide on a mold. I'd like to stay in the 250-300gr range, but not really sure about a bullet profile. I prefer SWC designs with...
Forum: Gunsmithing Tips & Tricks
Sorry for the slow response, but thanks!!
Forum: Gunsmithing Tips & Tricks
I have a late 70's Marlin 336 in .35 Rem, and picked up a newer replacement stock (with rubber pad). Fitting around the tang and up to the rear of the receiver is pretty good, but the issue I am...
Forum: Factory & Surplus Powder
I picked up 3k Tula SRM primers and just a hair over 14lbs of AA2495BR powder. I've never loaded any 2495 before, but should be just about perfect for most stuff I shoot.
Forum: CB Loads / Military Rifles
Will a .260 reamer effectively clean up a 6.5x50 chamber?
Forum: Case Forming / Re-forming
Ideally, I would like to use 1x fired LC '06 brass, but I don't like the idea of having to *potentially* turn necks.
Forum: Case Forming / Re-forming
I recently picked up a Mauser K98, and finding 8x57 brass has become a bit of a challenge. Fortunately, I have several thousand cases of 1x fired .30-06 brass...and looks like it *might* be somewhat...
Forum: Case Forming / Re-forming
I hate I missed this thread...local store had 3x boxes of Winchester factory loaded .225 55gr ammo for $29/box. I watched them for a couple months, debating on buying them for a rainy day, but...
Forum: Case Forming / Re-forming
The .25 Classic sounds really interesting...I have both .25 TCU & .25 Bullberry Contenders, as well as .30 & .357 Herrett barrels. The .30 Herrett really educated me about not buying a barrel...
Forum: Cast Boolits
Any suggestions on a heavyweight, shoot through any pig alive .45 cal bullet to load in a NEF Handi .45-70 single shot? Not sure I am quite ready for Garret 540gr loads, but something hardcast in...
Delusional.
.380 ammo is getting better, but its still a bit behind 9mm ammo...even 9mm ammo from the '90s.
Forum: Single Shot Guns
Any luck?
I just picked up '97 H&R "Whitetails Unlimited" .45-70 with Williams rear peep for $375, so there are some deals still out there.
Forum: Single Shot Guns
The couple I have played with (Super 14 and 21") had extremely long throats, long enough that I had a difficult time getting 175's to hit the lands...both were still fairly accurate, though.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |