Search:

Smith mountain but I mainly hunt Amherst County

Versa I too am from Virginia fish up at the lake all the time, I know of 27 bear killed from Gladys up to goshen and north towards cville I haven’t talked with my buddies that hunt Amherst area to...

That was the one thing I didn’t try that time was changing to the modified choke I am going to load a few more and report back

That’s a factory full rem choke the pictured target is right at thirty I didn’t get a picture of the 65 yard target it was dismal results, I have loaded a few more but slit the ctps wad about half...

Well I tried the same powder wads and .310 buckshot I had poured
27,28,29 grain charge weights 16 pellets each stacked by twos covered in bpi original
Ctps wad trimmed 1/4 inch off slit four time...

All had bpi original except the one 28 grain charge that wasn’t marked

Just got lucky I loaded some three inch in the ctps wad too but never got that good of a group they were stacked by threes so I am going to try them again stacked by twos see if it will tighten up

Here is a picture of the loads from full choke with all patterns marked
Slash was the 27
Circled 28
X was 29
The ones not marked was 28 with no buffer 300165

That was the spread it was the best group I had but I could also see the wad almost hit the target so the shot was just leaving the wad. I had some cut to the bottom of the cup but those were wider...

After reading tons of stuff and watching Wade’s videos I tried some 2.75 fiocchi hulls someone had given me. First off I like these better than the federal. I tried these below
Longshot powder ...

I ordered the advantage manual but i was thinking the same for the straight wall hulls, just making sure i get good data. I just ordered some stuff from bpi hoping ot comes in.

Thanks everyone for all the replies and advice this is the best site for loading i have been on. But a very addictive sport.

I was wondering if anyone had the bpi manual or any others i have one manual but dont have data that i need plus the bpi and tom roosters manual are sold out.
I just received my new buck mold for 0...

He is using a lyman expander die set for .224 the only reason his boolit is dropping light is because he asked for the boolit to drop at .220 so we didn't have to size it before coating it. He was...

would you consider posting this in the cast 223/5.56 compilation thread?
http://castboolits.gunloads.com/show...ilation-thread

I filled out the form for you below but I put ????? for the missing...

1-7 bullets are ww water dropped the tips are left exposed cause he made a plate sits the bullets in there tip down just to powder coat

268038

I got a friend into loading and now casting figured i would share his results. First off we are casting using a new arsenal mold no lube grooves and drops at 220 he is powder coating them comes out...

I will but looks like more home work for this project. I did start with two 1894s one 357 and a 44 both are doing great. I need to mod the 357 for the long -429 but its the best out of all my pistols...

Don't see many loads using this bullet anyone tried with good success? I have searched didn't see many at all wondering if it was just cause the swc don't feed well or what but a 170 grain pill...

I have the redhawk also but 7.5 using the 432-265 Keith design best I got was 21.5 h110 plain base. Sized to 431 done great around two inch groups.

Shot both the 357 and 44 today at a hundred yards both done well. The 357 I used 38s to get on paper then switched to some 358-429s in special brass four shots three were touching 12 grains 2400....

Not really just love to shoot keep telling my wife I am saving though!

I know if you watch armslist you can find The JM marlin's at a good price I picked up two in last few weeks looking for loads now and for five each! Good luck on your search hope it helps.

I'm trying to talk myself out of a Noe 360-180wfn style I have a few brand new lee molds I don't even use just don't like gas checks 358-158 lswc gas check 429-240 68 clone cause I found a four...