I have a very nice model 1901 Remington rolling block pistol that I want to shoot in a match. These were originally produced in either .22LR or .44 Russian, but this example is in 38 special. I'm...
Type: Posts; User: vernz
Forum: Single Shot Guns
I have a very nice model 1901 Remington rolling block pistol that I want to shoot in a match. These were originally produced in either .22LR or .44 Russian, but this example is in 38 special. I'm...
Forum: CB Loads / Military Rifles
Here are pictures of the threaded muzzle on my Johnson. I found a 2012 discussion about someone else who has a threaded muzzle and no one had any information on when or why. It looks like there was...
Forum: CB Loads / Military Rifles
Thanks everyone, you've given me some great information to get started with. I will join the Johnson Automatics forum and have already ordered the book. Now to figure out what to do about the...
Forum: CB Loads / Military Rifles
I just picked up a 1941 Johnson in 30-06 and would like to try it out using a cast load that will cycle the action. I searched this forum but did not find any information on loads. My initial gut...
Forum: CB Loads / Military Rifles
That's OK CHeatermk3. I along with his other fellow shooters didn't believe it at first either.
Forum: CB Loads / Military Rifles
The bullet is lead, but I don't remember which bullet it is. Nothing exaggerated whatsoever. I routinely shoot with him. We tend not to have a lot of wind where we shoot so that is not usually a...
Forum: CB Loads / Military Rifles
I just got myself a Greek Mannlicher Schoenauer 1903/14/30 carbine in 6.5x54 MS. My first step in preparing to fire it was to slug the bore and that gave me some trouble. My first 2 slugs came...
Forum: Group Buy Results
This is my first MiHec product and it is absolutely beautiful. This is also my first brass mold - can anyone tell me if there are any special break-in procedures? Does the mold need to be smoked...
Forum: Group Buy Archives
I am still interested in this buy as well. Patience is a virtue?
Vern
Forum: Group Buy Archives
Please put me down for 1 solid mold
jjakubo1 (at) nycap DOT rr DOT com
Thanks, Vern
Forum: Group Buy Results
I was checking up on this group buy and want to be sure I ordered correctly. I'm currently number 13 on the list for:
vernz......jjakubo1@nycap.rr.com..... one 0.462 mould with blank pins
I want...
Forum: Group Buy Archives
Please put me down for a 4 cavity solid mould
jjakubo1 (at) nycap DOT rr DOT com
Forum: Group Buy Results
Put me in for a .462 mould with a set of the flat base pins.
thanks, Vern, jjakubo1@nycap.rr.com
Forum: CB Loads / Military Rifles
I did not see any suggestions to use a very cheap piece of insurance....a dowel.
My mistake occurred a few years ago. I was helping a friend shoot my M1 Garand and had a failure to eject a round....
Forum: Group Buy Archives
Is there another list of ship dates? I'm not on the shipped or ship 11/1 lists.
Vern 12831
Forum: Group Buy Archives
Does anyone remember how much the brass was? I ordered 400 and 100 is for a friend. I don't know how much to collect from him for the brass.
Vern
Forum: Group Buy Archives
Please add me to the list for a 4 cavity all GC. I'll be ordering some gas checks too, but will do that separately as I'll get considerably more than 2000.
Vern
Forum: Group Buy Archives
I need one of these in .464 to hit the groove diameter of my 45-70 Peabody with Henry rifling. I know the 460 bumps up when cast with soft lead, but it has to hurt accuracy. Do any of the NOE molds...
Forum: Group Buy Archives
If others need the brass sooner I can wait until October for mine.
Vern
Forum: CB Loads / Military Rifles
I think .329 might be a little small for the M95. Mine run 330-331. Suggest you slug the bore.
Vern
Forum: Group Buy Archives
I'll take a 4 cavity gas check mould.
Vern
Forum: Group Buy Archives
I will take a 4 cavity mould in .311.
Thanks, Vern
Forum: Group Buy Archives
A check is in the mail for 400 cases for Vernz, zip code 12831. It will get picked up tomorrow.
Vern
Forum: Group Buy Results
I'll be thrilled if it drops a little bigger than 460, but put me down for a 4 cavity plain base mould.
thanks, Vern
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |