302231 purchased in 1975. Malcolm scope added a few years ago.
Rick
Type: Posts; User: Rick459
Forum: Single Shot Guns
302231 purchased in 1975. Malcolm scope added a few years ago.
Rick
Forum: Reloading Equipment
well when they mentioned that it would not work with the Roller handle it lost my interest.
Forum: Swaging
here is a video of a friends YT channel that i sent some .45acp bullets made with .40s&w cases for jackets using a .243 sizing die that i modified to test in his balistic gel. also i sent him some...
https://castboolits.gunloads.com/showthread.php?435088-wts-Lyman-310-dies-bonanza-bullseye-powder-measure
Forum: Shot Loads For Pistols
Ohio Rusty...don't have a scanner but here are two photo's from page 593 and 594 speer#13289704289705
Sent from my SM-N960U using Tapatalk
Forum: Reloading Equipment
another trick to help accuracy with lead bullets is to champher the case mouths either using a VLD champher or the K&M inside neck reamer that uses a 4 degree cut angle..
Rick
Forum: Cast Boolits
......https://uploads.tapatalk-cdn.com/20211005/237d0a187c42f653e88db0f28a3cb128.jpghttps://uploads.tapatalk-cdn.com/20211005/665d7c08d039cf1b4d10e0a4d4c40a01.jpghttps://uploads.tapatalk-cdn.com/20211...
Forum: Cast Boolits
what's your bore slug out too? I have some lubed and sized....458..bullets I could give you some to try. the weights range from 380-435 with large meplats
Rick
you are correct about the dish on the bottom of the punch. I used a 1/2" ball end mill to perform that part. 289635289636
Sent from my SM-N960U using Tapatalk
I am just a hobbist.everything I produce on my lathe and mill are for personal use. my tool did not come with a large punch or any large primer shell plates. so I have nothing to go by. I tried...
your punch is ready...
289585289586
Sent from my SM-N960U using Tapatalk
is this the tool your talking about.if so I will see if I can duplicate it this afternoon on my lathe.289567289568289569
Sent from my SM-N960U using Tapatalk
Forum: CB Loads / Military Rifles
Small rifle primer pockets .118 To .122
Large rifle primer pockets .128 To.132
Small pistol primer pockets .118 To .122
Large pistol primer pockets .118 To.122 these are the primer pocket depth....
So being that I have 2 of these molds, I decided to modify 1 of these to drop a flat base bullet. I tried to modify the plug but cut it back to where it dropped a 435 +or - bullet but it needed a gas...
Forum: Reloading Equipment
although the 650 does not resize you can either install a sizing die or use your lee load all to deprime and resize the hulls then run them through the 650.
Rick
Forum: Single Shot Guns
I only have 1 barrel now and it is chambered for the 6.5 carcano. I used a old rusted out 7 tcu barrel that I had laying around and used it as a stub with a 6.5 shieln barrel that was gathering dust....
Forum: Gunsmithing Tips & Tricks
https://www.brownells.com/gunsmith-tools-supplies/stock-work-finishing/stock-bedding-accessories/bedding-fixtures/garand-sku080727001-832-3145.aspx
Forum: Gunsmithing Tips & Tricks
i have a carcano reciever no barrel on it i have already orderded a new unthreaded and unchambered 6.5 barrel for it from E.R. Shaw, and now i am trying to find a gunsmith to thread and chamber this...
Forum: "The Barrel Works"
on Shaw's website they will not do the carcano recievers among other recievers.
Forum: "The Barrel Works"
i have a carcano reciever no barrel on it i have already orderded a new unthreaded and unchambered 6.5 barrel for it from E.R. Shaw, and now i am trying to find a gunsmith to thread and chamber this...
Forum: Gas Checks
you can use this as a guide....
http://sebagosales.com/gaschex/Check-Maker1&2.pdf
Forum: Reloading Equipment
i was able to purchase mine for $175.00 on ebay only because it had a bent handle. never try to do any swaging with the handle set for reloading cartridges because you can not set the swage to grab...
Forum: Casting Equipment
they are still taking orders just ordered a set for my RCBS Pro Melt and will be here Tuesday full review after.
Rick
Forum: Casting Equipment
Other than Magma who else makes a affordable bullet casting machine?
Rick
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |