I miss my old bench, it had a 1/4" thick stainless top that was 3'x10'
Type: Posts; User: John Taylor
Forum: Special Projects
I miss my old bench, it had a 1/4" thick stainless top that was 3'x10'
Forum: Single Shot Guns
About the only way to drill after welding is with carbide. At this point even going with a bushing it will take carbide to machine for the bushing. I usually make the bushing out of spring steel (...
Forum: Swappin & Sellin
round barrel chambered for 40-50 SS. With reloading dies. $3,000
Forum: Swappin & Sellin
Lever action 44-40 with 3 digit S/N, most likely made in 1880. a little rough but has good rifling. Asking $3,000
Forum: Swappin & Sellin
Can do barrels 48" long. Has sine bar, rifling twist from about 1 in 8" to strait. Auto indexing for 5, 6, and 8 grove, hand indexing for 2,3 and 4. About 20 cutter boxes for different calibers, 7MM...
Forum: Single Shot Guns
Several years ago another shop sent me a 44 that they thought had been re-chambered to 25-20 WCF. When I cast the chamber I found it was a 256 Winchester, a little hot for a 44. I talked to the other...
Forum: Single Shot Guns
Lining the barrel is no problem. 25-20 single shot might be a little tough finding brass, but then so is 25-20 WCF. Buffalo arms has ammo but at almost $5 a shot. You can find 25-20 WCF for under $3...
Forum: Gunsmithing Tips & Tricks
This one will most likely work but you might want to get the screw at the same time as it most likely will be metric....
Forum: Gunsmithing Tips & Tricks
https://homesteadparts.com/shop/winchester-1873-c-1_4.html
Forum: Special Projects
I have done the chamber liner more than a few times. I usually solder the sleeve to the liner and then turn it to fit the chamber. The reason for solder is that loctite will let go if you get it to...
Forum: Gunsmithing Tips & Tricks
The first model was 44-40 only with 5 grove rifling, carrier was most likely not marked. Later models had 6 grove rifling and came in 44-40, 38-40, 32-20 and 22 short and long. Some of the last...
Forum: Gunsmithing Tips & Tricks
A customer sent me four 1877 Colt revolvers in a paper bag. They were all disassembled and the frames had been color cased. Mixing and matching parts I got two together that worked. The other two I...
Forum: Single Shot Guns
Thanks, that's what I was referring to, a case with a rim and strait wall. The 50 BMG that separated was a factory round made in 1951 and the brass had become brittle from age. Headspace can be a big...
Forum: Gunsmithing Tips & Tricks
I just did a 5/8-24 on a 44 mag last week for a customer. A customer ask me to do a 1/2-28 on a 357 a few weeks back and after doing the numbers I found that the wall thickness would only be .025"....
Forum: Single Shot Guns
Head separations usually are caused by to much headspace or old brittle brass. Easiest way to get them out is pore a chamber cast and push it out with a cleaning rod.I had a brass rupture on an 1876...
Forum: Leverguns
The nickel steel came out in 1895 for the 30-30. The early barrels were marked nickel steel. Most of the problems with the barrels was caused by corrosive primers.
Forum: Leverguns
There was a lot of variation in chambers for the 38-40 and 44-40 way back when. You might want to keep your brass separated so you don't over work the brass and neck size only. modern factory ammo...
Forum: Single Shot Guns
Looks like a #5 action, never seen one in 43 Spanish. Most were 7X57. Should be fine in 44-40. If it were mine I would probably go with a new barrel at 26" long.
Forum: Single Shot Guns
According to TJs the bore is .420 and groove is .428 on their liners. These are hammer forged from 4130 steel.
Forum: Single Shot Guns
My book says that 205 grain with 1 in 36 should work fine. So a 1 in 24 should be fine also.
Forum: Single Shot Guns
Most original 44-40 rifles had a 1 in 36 twist. TJ's liners has 1 in 24 and 1 in 18"
Forum: Single Shot Guns
Looking through my barrel pile I found a cadet barrel marked 32 Special and another one marked 32-20 and one that has not been messed with.
Forum: Single Shot Guns
I picked up a Cadet action and wood several years ago and went the other way, it's now a 32 S&W with an octagon barrel. It's almost like shooting a 22 LR with a little more knock down power.
Forum: Gunsmithing Tips & Tricks
The protrusion should be .050" to .060".
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |