Search:

oh no it affected balance, not that bad though. putting it up front helped control recoil and muzzle flip better than in the butt. glued it right in the hollow of the forend but you could always...

I glued one in the forend, way more effective than the butt
I used 2ton epoxy, scuff up the surface of the plastic, wipe with mek, repeat, then put in a little epoxy, put the tube in, then fill with...

You can buy an interchangeable counterbore set for not much money, or simply step drill it with progressively larger bits
I’d rather do that than mess with my trimmer

If you “ open them up” as you say
You will need to make a new piston to fit or you will have lube squeezing out everywhere at .001-.002 thou over
Cheaper to just buy what you need

Controlled burning reduces tick numbers as well. What about the sacks of pesticide powder i see hanging under cattle feeders, in barns, etc? I would think that would be effective as well from a...

Yup
Modern high temp bearing grease is best, especially on the line or in the south
When temps rise or the gun warms up, lubriplate and most other grades run and fling
Red high temp bearing...

Duracoat and durafill

IIIRC youre in Vicksburg, so those are Miss River Barges. Not often do they take them out of the water for repair, usually most stuff is done in water, unless its really bad like major welding,...

for that price you can send it out and have it back bored and extrusion honed and keep most of that money in your pocket.

Way back when I got in a group buy for a special run of Lee 5.45 dies, I simply formed brass from 556 nato brass. simply trimmed, it about 10-.20 thou long, sized in a 222 die, then anealed it and...

Ptg unithroater is what you want
No lathe needed, turns by hand and stays concentric to the existing throat
Most throaters need to be used in a lathe to get good results.
Before you do that...

Brownells sells a kit which is a modified brake cylinder hone
Comes with different grit stones .
That’s what I use, but keep in mind, if it’s badly pitted you bay need a backbore reamer to fully...

I’d like to see him also test those same barrels with an xrf gun to determine composition
While hardness is important, steel composition is important as well and annealed 4140 can be similar in...

Doubt it was a squib or stuck bullet
If I was a handgun maybe , seem plenty of bulged 38’s, 9mm’s etc but even at low handgun velocities the barrel is sufficiently bulged on the outside to be seen...

Mike orlen

ridgid dark or oaty dark, all I use for stainless and cm barrels.

If they’re keyholing with jacketed bullets
Not much you can do other than rebarrel
You can try to counterbore if it’s a muzzle erosion issue but unless you have a lathe, generally not worth it

I’m in Brusly / Baton Rouge
When you get your barrels turned down get with me

where in LA are you located, if all you need is threading I can help if your not in a rush

Delrin / nylon

get a larger aperture. On all my palma/match rifles I use adjustable iris front and back. As Ive gotten older the rear iris gets bigger, the front stays the same but I put a magnafying lens on it. ...

Heck if you can move quiet in the woods, walk up behind them downwind
You can football punt them or catch ‘em lol

What kinda armadillos do y’all have there? Up armored?

I’ve killed thousands with various pellet guns over the years
22’s too

Quick answer, no you wont get into trouble for tossing an airsoft grenade at kids violating the law, but you may loose your life.

IN LA a "vehicle theft" as you call it even unlocked is still...

Those Lincoln tombstone welders are pretty simple to work on and there's lots of info to diagnose them on the web. take the back and cover off, look for a burned or shorted wire (spiders and mice are...