@stockcarver
Type: Posts; User: Arrow
Forum: Gunsmithing Tips & Tricks
back to top? Any info on threads used or dimensions on ejection port and loading gate?
Forum: Gunsmithing Tips & Tricks
Did you get a chance to review your notes to see what thread size the receiver was opened to as well as dimensions of the loading gate and ejection port? Thanks
Forum: Gunsmithing Tips & Tricks
Thanks for all the info. What thread size did you open the receiver up to? Also what are you doing with the receiver in the lathe with the mandrel running through it, you said something about...
Forum: Gunsmithing Tips & Tricks
I build custom boltguns so I'm very comfortable on the mill and lathe. Ive never really worked on lever guns and have been kicking around the idea of turning my JM stamped 1895G into a 50 Alaskan...
My Glock 20 also does the same thing. I know there are many people out there shooting this bullet in their glocks without any trouble. I understand every gun is different but we're talking glocks...
Yes I am shooting the 200 and 220 mihecs. I will try a 1.260" and see if that fixes things. What do you mean "tune" for heavy bullets? When I cycle by hand it feeds just fine every time. Defiantly...
I'm shooting a kmm barrel wolf guide rod and tried both 17 and 22 lb wolf recoil spring. Works pretty well with various jacketed ammo but when I shoot the mihec wfn through it with anything from...
I have no problem admitting when I have screwed up. For example I load 220 grain hard cast wfn bullets of 8.4 grains of longshot in 10mm for my kkm barrel in Glock 20. For whatever reason I shot them...
Thank you very much for all the advise. I don't think it could have been pushed back into the case. Like I said, these bullets are pretty big diameter and it's pretty tight going into the casing. It...
My buddy has an xdm 5.25" 9mm. He just swapped out the barrel for a stormlake threaded barrel for a suppressor. The ammo we are shooting has been shot in my Glock 19 with a factory barrel and a Kkm...
Forum: Cast Boolits
Thanks for chiming in Oreo. I also was able to get these bullets to feed flawlessly while hand cycling the slide. Something is happening while shooting and I promise you it isn't limp writing. Any...
Forum: Cast Boolits
I see where your going with slide velocity. I do have a 22 lb recoil spring in. I have tested many different levels of "heat" for loads. I just don't see how it could be my mags when I have 6 of them...
Forum: Cast Boolits
I have 6 mags for my glock 20 and all feed perfectly with jacketed. 1.245" wasn't the only one to feed by hand. They all fed smoothly but 1.245" was just smooth as butter. I don't understand why it...
Forum: Cast Boolits
Thanks for all the advice guys. I am defiantly not limp waisting. The loads are defiantly hot enough. I have shot very light loads all the way up to nuclear. Like I said before 0 problem with...
Forum: Cast Boolits
This is about the 3rd of 4th time i have posted about this same issue. I am still getting leading with my glock 20 and 29 with factory and kkm barrels in each. I have tried everything and have...
Forum: Group Buy Archives
220 grain 4 cavity with all pins with lube groove.
Flyfisherman246 at sbc global dot net
I have shot the glock factory barrels and they lead too with this loads. They have sloppy chambers so I'm sure I can get them to run with a bigger diameter bullet. I am ultimately looking to use...
I have also tried water quenched. I measured slug with a micrometer. Bullets sized at .401 already have a hard enough time chambering. (Multiple rounds won't fully chamber) if I were to size to .402...
I have slugged my barrel and it was .400". I have tried carnauba red and lyman moly lube. I have tried light loads all the way up to hot. I don't understand what is wrong. I have tried everything I...
I shoot a glock 20 and 29 both with kkm barrels. I am casting with a mp 200 grain Cramer pin mould sized to .401". My notes are .400". I have tried wheel weight alloy, 1/2 ww 1/2 pure, and 2 part we...
Forum: Group Buy Results
I'll take one. 4 cavity, plain base, hollow point with all pins, .432. Fly fisherman two four six at sbc global dot net.
Forum: Group Buy Archives
So when are we doing this 220 wfn mould?
Forum: Group Buy Archives
The way I see it not many people would be using a 220 grain bullet in a 10mm for plinking. It's kind of a waste of lead. There are much lighter bullets out there that will still punch a hole in paper...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |