I'm looking to trade 500lbs of pure sheet lead. Coww form is good, ingot form if it's contaminant free and clean.
Type: Posts; User: mdntranger50
Forum: Completed Deals
I'm looking to trade 500lbs of pure sheet lead. Coww form is good, ingot form if it's contaminant free and clean.
Forum: Completed Deals
Thanks for the offer Rusty, Im looking to trade a large amount and ftf trade as well since shipping would be too much.
Forum: Completed Deals
I have a supply of pure sheet lead that's still in sheet form, I have left it in sheet form so you know it's truly 100% pure lead. I would like to trade some of it for either COWW lead or an already...
Forum: Lead and Lead Alloys
Thanks for all the replies, I did find Bumpos calculator and have been playing around with it. With this calculator it says 2 2 96 is 11bhn but also 1 2 97 is 11bhn. I will just have to alloy a batch...
Forum: Lead and Lead Alloys
Seems this mix may be more around 8bhn from further reading on the lasc site.
Forum: Lead and Lead Alloys
I have a little supply of pure sheet lead still in sheet form. I was going to try to trade pure for WW lead or lead already alloyed to around 9-10 bhn. I mostly cast for pistol and powder coat...
I have seen some guys use a hot plate to preheat their molds and then sit the molds on if they have to take a pause. Thought about doing this but idk, I find more simple is better for me.
Thanks for the replies. I have a little wooden dowel I tap on the handles on my Lee molds when they don't want to drop out. This is mostly when it's getting up to temperature after it gets in the...
Forum: Cast Boolits
Loaded some 124gr HST into Federal nickel cases with cci primers over 5.8gr BE86 which duplicates factory standard pressure loadings at 1150fps out of a 4" barrel, very accurate loading for me as...
Forum: Completed Deals
I will take #2 750+ .223 cases for $38 delivered
Forum: Shot Loads For Pistols
Interesting thread, never thought of doing this but gives me more food for thought. Thanks for all the replies and info. You guys are great.
Forum: Cast Boolits
I got started later in life but have been enjoying it the last 3 years. My latest brain fart has been how to source local ranges for bullet scrap in the berms. Trying to figure out a way to convince...
I just aquired a Lyman 2 cavity .308 mold. I have only used Lee aluminum molds the last 3 years. How much difference will this iron mold be. Any tricks to get started? I'm kind of reluctant to try it...
I still only use 2 cavity because I already have a dozen of them and I'm kind of slow anyways, not just physically but mentally too.
Forum: Lead and Lead Alloys
Look up videos of Elvis Ammo using zinc to cast bullets. He burnt out one of his pots melting it down.
Forum: Cast Boolits
Thanks to all for the insight. I figured it was just manufacturing tolerances but I didn't think it would be that much off. I do not have a problem with these molds as far as casting and they both...
Forum: Cast Boolits
They both measure .3575-.358 as cast then after PC they are .359-.360 I resize to .356 for 9mm and .358 for .38spl
Forum: Cast Boolits
I have a Lee TL356-124-2R 124gr mold that drops at 120gr and a Lee 356-125-2R 125gr that drops at 130gr. Both with the same alloy and in the same casting session. Someone tried to telling me that's...
Forum: Cast Boolits
I loaded up some 9mm 124gr HST in Nickel federal cases, cci primers and BE86 powder. They chrono 1150 fps out of a 4 inch barrel. My duplicate load compared to factory standard pressure 124 HST.
I tried it the other way around with ginex small pistol magnum primers in low range .223 55gr fmj loads. They worked ok but were super flat. I only did a test of 10 just to see if it would work for...
Forum: Cast Boolits
This is something I have been wanting to try to do. Thanks to everyone for all the great info in this thread!
Forum: Coatings and Alternatives
I just add a hand full every now and then to my pot so I don't over load it with powder coat material.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |