Search:

One of these

https://m.media-amazon.com/images/I/71N5bAedAVL._AC_SX679_PIbundle-3,TopRight,0,0_SH20_.jpg

I have had the same experience with this nose rider design. Fine tuning the nose diameter with NOE push trough nose sizing dies cleared the issue for me. I wasn’t excited about purchasing more tools...

Sounds like you’re set on everything else but powder. If so, I’d look up what your manuals have for that weight that appears most on two fronts: the manual and the shelf, and then order some. Powder...

If it were me, I’d keep the different lead separate. You can melt and remelt to get fluxing experience, but I’d just cast from the ingots you already have to get started. Once you see the first cast,...

I vote bubba rountree on YouTube. I don’t know of a one stop shop, but there is some overlap of payload weight it seems. I have the bpi buckshot manual and like it for the components I have on hand....

The command series of Kohler engines are tough. I’m in the Lawn business and have a couple with well over a thousand hours on them. The horizontal twin opposing cylinder Briggs engines might be...

If I’m not too late to the table,

marksvw at aol dot com

4 cavity hollow point GC all pins

Thanks, Mark

Look at the ender 3 or the ender 3 pro. Creality is the “brand”. I’m not all that tech savvy and figured out how to use a program called cura. YouTube has info on both. The printer is less than $200...

I’m going against the grain and suggesting your crimp is fine. The pill is too fat for the lands/rifling at that particular seating depth. Dummy up a round and seat it deeper. I don’t know if all the...

I like it! I recently got a Keter workbench for reloading in the RV and this gives me some ideas. Looks like a predecessor to the inline fab type reloading bench accessories. Love the pic, and great...

Please remove me from this buy.

Thanks,

Mark

Sell them now. Prices are up, keep all you want, but sell is my advice.

My sisters (ex) husband passed away and left stuff for my sisters kids to deal with. My sister ended up having to handle the...

Britts donuts in Carolina Beach NC!! It’s not just the donuts, I think the near ice cold milk they serve with them makes for an experience. It’s tucked in the old board walk. Absolutely delicious!

I’d like to be added to the HP 4 cavity brass mold list.

marks vw at aol dot com

Thanks!

Nice lever action , check in over at the Rossi forum. Great wealth of info.

https://www.rossi-rifleman.com/index.php

Mark

Looks good. I might have to try this on my Lee 300 BO die. It cuts the nose on the c312-155 . Puts a perfect circle on the nose.

Good job.

Mark

To isolate the problem to the carburetor, slowly slide the choke toward the choke position. (While it idles) If it cleans up and stops surging it points to a dirty carb. My money is on the carb, we...

Elkins45, that’s a generous offer! I’m going to have to decline as I have a nitrided barrel and am pretty sure it would ruin a reamer. The barrel has chambered the 312 160 2r; 312 230 5r; and 311299...

I have had no heat in my 98 f150 and was sure it was the heater core. Well, it sort of was, but the main issue I had was the water pump. I had an issue with corrosion in the coolant but did not know...

I appreciate all the help offered on this mihec 311-230-hp mold. To help with anyone else having purchased or plans to purchase this mold, I’ll explain again the issue.

This is what I would...

So frustrating! Yes it casts larger than.300 and is per design according to Miha.

Anyone interested in this mold?

NOE is currently out of his sizer kits.

Anyone have a .300 or .299 nose...

This is a bore rider, correct?

If so, that’s the issue. A nose of .301 is not readily accepted by my barrel. My best pound cast is yielding a little under.300, like .2995. I do not see a...

Miha,

Yes I have tried this bullet sized to .309, un coated with same results. This is a picture of the marks the lands are engraving in the nose.255782

I have a no lube groove gas check mold. The bullets are hourglass shaped. They measure.295 between the drive end and the nose that measures .301 after powder coat. They were cast from some of the...

Mold arrived this morning. Nice and long boolit, can’t wait to fire up the pot and crank some out. Thanks to our Honcho for sticking this one out.

Mark

255522