Search:

From my 1963 Rem 700 with factory 20" barrel.
Ranch Dog 165g GC powder coated.
The 0615 holes are under the dime :)

The previous owner of my Ruger 45 convertible had the acp cylinder trued to .452 by a local GS and the colt cylinder to .452 by Doug P.
I don't know if they needed it but it is the most accurate...

I hope someone comes along and answers your question. I am scheduled to look a senior tomorrow with a box full of I don't know what parts!

Lee classic here. I took it as part of trade, my good fortune I guess. I haven't it long but after setting up 38, 357, 44, 45 acp and 45 colt shell plates, I wondered why it took me so long the get...

Thanks everyone for the most excellent information. The buck horn is off and eventually to be replaced with filler or home made filler as the pictures suggest.

It shot well but now have a peep sight issue.
https://castboolits.gunloads.com/showthread.php?458241-Pre-64-Win-94-with-Williams-Fool-Proof-peep-sight-question-buckhorn-conflict&p=5598709#post5598709

Trying to get the peep dialed in (50 yds for load development) and I am finding the peep is down and very close to the barrel. So close the rifle's buckhorn rear sight occluding(sp?) the peep. Is my...

Well after several alternate copper solvent soakings and patching out, I began to see some clean patches. Followed by a few more with Ed's Red and now the bore is patch clean.
I sorted through a...

A good friend recently gifted me a 1954 model. I don't know much about its history but I suspect it was feed J words all its life.

Which brings me to my question, I will be shooting cast only in...

I was looking for something for a gp100 but sadly there was no gp100 among those on the drop down menu.


Sent from my iPhone using Tapatalk

Thanks Dinny.

I have come into a quantity of each, 200g RNFP up to and including 250 Keith SWC. I'll be loading and testing in with a 44 special and 44 mag hand guns.

My question(s) is do you shoot one before...

Following the thread with interest as I hope to get my 357 to the woods in a few weeks. My 44's are po'ed.
Trying not to derail the OP's thread and if not appropriate please chastise me accordingly....

Yes, there is no question of the powder, the ammo was previously loaded by me and is Unique. Other than a kernel or two (flakes) attached to the boolit which I discarded, the powder is clean. It will...

I have quite a few loaded 44 mag cases with a lubed cast boolit that I will be pulling with an inertia puller. I expect to be able to reuse the components, however, I have question regarding the...

I did not.

I wish they were 170's but after weighing a dozen or so @ 160 , I couldn't make em gain any weight. ;)
Thanks to my poorly formatted op, the 160g weight showed up after the pic.
Thanks

Lee C309-150F, my thought as well. Thank you gents.

Found a couple of hundred of these amongst my stash. And have no idea where I got them. They sized to .310 and weigh 160g....

I am away from the bulk of my stash but I found few to try. I really don’t see the project as a big deal.
A handful of boolits , mixed lot of carnuba red and Alox were boiled in water for about 5...

Yes you do ;) and that someone is going to get a handful of each for PC'ing/sizing after I de-lube em. He has had a successful trip down this road and saving the gc's is also a plus. It will be a...

Ed, the test would include a very small number to start. Thanks.
Gary, easy is my middle name. I'll try a few with some tape. Cig papers perhaps? Thanks. Laissez les bon temps roulers.
Gp, good to...

I have come into a large (1300+) quantity of cast boolits, Lyman 311041's and RCBS 30-180's. They are sized at .309, gc'ed and lubed. However they do not shoot well with my two 30cal rifles. Since...

This +


Sent from my iPhone using Tapatalk

I first would like extend my thanks and appreciation to those of you both on and off list, who shared their tips, suggestions and encouragement. I was ready to send this rifle to the j word shooter...