Search:

You have PM :-)

I just took a Lee case feeder (for Pro 1000 or Loadmaster) for small cases (the one with an aluminium funnel), popped out the aluminium funnel and chucked it in the cordless drill and used emery...

You were more lucky than me. I was chronographing a 44 Mag load, when I hit it

http://castboolits.gunloads.com/imagehosting/thum_66074f89a0cfccc0e.jpg

RCBS 44-250-K with a large meplat really...

Arceagle,

I started casting for the 9mm with the Lee 356-120-TC mold and they weighted 130 grains. I didn't think much over is and tried in my SVI Infinity with OK results and no leading. Sized to...

I'm currently working as a System Engineer at FMC Technologies in Norway. Been at the company for 6 years.

I've also worked with glass to metal sealing.

Before that, I was a production planner...

10 - 15 k a year in competition and training.

Mostly .22 LR and 9mm, but I also compete with
.32 H&R MAg
.38 Special/.357 Mag
.44 Mag

I've had good results with the "Medium Hard alloy" on the lasc site:

Monotype - 3 pounds
Clip-on Wheel Weights - 4 pounds
Lead - 3 pounds

It was a bit hard for my liking (BHN 16 ?), so I've...

Yesterday we finally got the engagement rings from the jeweller and today was the first day with the ring on my finger and a fiancee waiting at home.

The three feet of snow is starting to shrink...

It can be done, but it's not the optimal setup.

1. You have to find a way to fasten the chain for the powder measure in the carrier in station one. I'll guess it can be done if you tinker a bit...

Tinn Norge is Norwegian for "Tin Norway". I've also bought some of it that I have melted down into 1/2 lb bars.

Season Greeting from Norway

I've also made the Molybee lube. It is very simple to make.

Poured it in my Star and discovered the air-hole at the back the messy way :shock:

The lube don't require any heat and is a bit...

And up on the first 8 inches of my forearm. I looked like a mess after 350 rounds with the molybee lube. Was a bit concerned until I discovered the same lube residue when firing 250 rounds lubed with...

I've made up a batch of molybee lube (50/50 moly grease and beeswax).

Compared to Lars Carnauba Red, the accuracy is the same and I have experienced no leading.

However, the spent brass has a...

I would guess you need some heat.

The pump plunger on my Star is very slow, just before the heater kicks in. I'm using Lars Carnauba Red.

50 lbs linotype, 700 lbs of rangescrap (14BHN), 100 lbs WW, 100 lbs pure, 120 lbs ready to cast alloy and 200 lbs of alloy I have to blend with pure.

20K SP primers.

When melting down range scrap, I tried to empty a bucket of wet rangescrap into about an inch of molten lead - will not do that again. I tried first with one boolit that melted, a fistfull that...

Picket up another 200 lb of range scrap yesterday. Took me about an hour to collect it.

I've just discovered the berm of our range hasn't been mined - ever!

It is probably several tons of lead there and 45 minutes produced some 200 lbs of lead.

I've bought a bicycle basket made of...

Have you just smelted/melted/redered the range scrap that is 7 BHN? If you wait a couple of weeks, it might rise to 10 BHN.

Best Regards

I sent him a message that I got a reply for on March 18th.

Apparently, he bought a RCBS mold for the 9,3mm and wouldn't participate in the group buy.

No, I have a 2000W hotplate ;)

Lee W:

Thanks for the link. I'll think I'll order the DOH Tek-Lok SR-Loop holster - if they send to Norway.

Regards,
Norseman

I'm using the 105 grain SWC with 2,8 grain of VihtaVuori N-310. No crimp and the bullet nose 1mm under the top of a .357 Magnum case.

Very accurate in my 6" Ruger GP-100 and I don't have to try to...

I have the fortune to have a SVI 6" Single Stack.

Unfortunately, I don't have a holster for it. I'm looking for a holster to transport it between stages in Norwegian field shooting competitions....

I've found out that the heater setting is the same (or a fraction less with the Carnauba) for the Magma heater, using Magma og Carnauba Red lube.