Search:

AMP....if you have the $...I don’t.

Well said, Petrol & Powder.

Wonder of wonders - found some 17 Mach 2 in Scheels Overland Park, KS yesterday!! $9.99 a box - no limit. It was CCI.

Use it - White Label Carnuba Red in everything from .32 pistol through .44 Mag and even .223. Excellent hard lube - got to have a heater tho.

Shield. Just not enough grip size in the Ruger. Probably have 8 to 9 hundred rounds through mine with no problems.

J-B 'non-embedding bore cleaning compound (got mine at Brownell's) works. I shoot 124 tc lee sized to .358 over 3.9 bullseye in all of my 9's (Ruger, S&W, Springfield Armory, CZ) without leading so...

I got this mold a while back in 4 hole brass hp. It drops like a dream and the 4 banger is almost as quick as a lee 6 banger! One thing to watch out for is the pile of boolets you end up with - you...

Thanks again, guys. My CZ does indeed have the chamber capable of 5.56 pressures. I've used 72 grain cast just kissing the lands with OK accuracy. My goal is to match my other CZ and Savage which I...

Appreciate the replies. But, has anybody experienced any grouping differences with a .5 grain variance from an "average" weight? e.g. do boolets weighing from 63.0 to 64.0 group just as well as if...

Had mine since 2015 and no problems other than an occasional "Error" message on start-up. Unplug and re-plug and it goes away.

This is what I did to accommodate any mould other than bottom pin HPs...

Too cold and windy to go check now so thought I'd ask the audience.
I'm shooting a CZ 527 Varmint 1:9 w/24 inch bbl for my NOE 225-65FN GC in front of 11.0 Gr of IMR 4227. I'm getting boolits lubed...

Should be here Monday - looking forward to seeing what it can do compared to my CZ 75BD Police. I'm sure both are more accurate than I am!

Springfield Armory Range Officer Commander Elite 9MM

Don't have a 'for sure' solution but I've had mine for 3 years. On warm-up it occasionally shows 'error' and stops heating. I just unplug it for a minute or so and it 'resets' and works fine.

Vortex. I have used the 'customer service'. Received a viper in 6x24x50 that had a frozen drift turret. Ordered on line so no way to 'check it out'. Emailed them and two days later I got a email from...

I'd give these folks a call and see if there is something like a Sako pin that would work.
Numrich Gun Parts Corporation
226 Williams Ln.
Kingston, NY 12401
Phone: 866.686.7424

I, too, was a beneficiary of his expert advice. Sent a NMB 9mm cylinder to him because it wouldn't fully seat my 9mm cast - sized to .356. Autos handled them fine. Turns out I had my seating die and...

This goes under the unheated luber-sizers, like the Lyman 450.

I just looked up the RCBS heater - says "coming soon" https://ads.midwayusa.com/product/209992/rcbs-lube-a-matic-lam-heater-120-volt ...

Rebel - if you are asking about my post - it works for either.

No experience with the RCBS device mentioned but I made my own using a standard dimmer switch, single outlet and plastic double outlet box. Just find an old appliance that doesn't work and use that...

Only time I’ve seen something like that on a LCT is when handle strokes were not the same...e.g. short strokes ��

I've been loading 9mm for several (5+) years without a problem (or so I thought) - using Lee FCD. Recently tried using reloads in Ruger convertible and the rounds wouldn't chamber completely - about...

Armadillos...in Denmark...seen as far north as Emporia, KS but the didn’t have to swim much����

OOPS, didn’t see that you sent to TX, my bad😔

Welcome to the dark side!

For what it’s worth, I just put on a few hundred .416 “rifle” checks on my accurate 41-210TC boolets. They are loose to start and a touch of lube helps hold them on to get them in the sizer but once...