I'll take the 8 cavity solid aluminum mold
Thanks
SAJTU
Catlynu at Earthlink dot net
Type: Posts; User: SAJTU
Forum: Group Buy Archives
I'll take the 8 cavity solid aluminum mold
Thanks
SAJTU
Catlynu at Earthlink dot net
Forum: CB Loads / Military Rifles
I finally found some time to cast up a batch of boolits out of the NOE 311-188-FN Hunter mould. This mould cast like a dream once you get it up to temperature. Ended up casting up a pile of...
A buddy gave me a couple hundred once fired 7.62/.308 PVRI Partisan cases. I've reloaded these multiple times with both j-word and boolits out of my FAL and never had any splits, separations, or...
Forum: Group Buy Archives
I'll take one sprue plate (standard hole) and one cam lever.
Thanks
SAJTU
Forum: Group Buy Archives
I tend to be pretty patient type and have been involved in some long group buy waits in the past…but this one is getting little “long-in-the-tooth”. It seems a very similar boolit moulds is now...
Forum: Group Buy Archives
338
I'll take a 2 cavity mold - .311 GC.
Thanks
SAJTU
Forum: CB Loads / Military Rifles
offshore44
I don't use small base dies for cases for StG58, just a FL Redding die set. I assume the chamber is fairly generous on the Steyr barrel and have used everything from GI brass to...
Forum: CB Loads / Military Rifles
offshore
Let me know and I'll send you a few of the MiHec boolits to try out of your FAL. Maybe a little filler would help accuracy with your 35.0 gr Varget load. I usually use a 1"x1"x1/2"...
Forum: CB Loads / Military Rifles
I finally did some cast boolit testing over last couple weeks that might be worth posting. With the cost of 7.62/.308 ball ammo too much for me to justify shooting my FAL STG58, I finally did some...
Forum: CB Loads / Military Rifles
Jimb 16
That's interesting, out of the 8 carbines I have, only the Saginaw Gear leads with boolits in the last couple inches of the barrel. It brushes out easy so don't worry about it too much. ...
Forum: Group Buy Archives
I'll take one 2-cavity solid mold.
catlynu at earthlink DOT net
Thanks
SAJTU
Forum: CB Loads / Military Rifles
I've got a few M-1 carbines and shoot lead out of all of them. I tried an number of molds (Lee and Lyman) that cast carbine boolits but the NOE 311-115 RN mold is really outstanding. It seems to...
Forum: Group Buy Archives
Mould arrived today. Man, it's nice...almost too nice to use!
Thanks Miha
SAJTU
Forum: CB Loads / Military Rifles
Great cast boolit in my M1 carbines. I use water-dropped with GC sized at .310 with 14-14.5 grains H110. About USGI ball velocities and a similar accuracy. No leading so far in different carbines...
Forum: Group Buy Results
Swede
Payment sent by PayPal.
Thanks
SAJTU
Forum: Group Buy Results
Swede
If it's not too late, put me down for a 3 cavity GC .314 drill for probe.
Thanks
SAJTU
Forum: CB Loads / Military Rifles
I've used 5.7 grains Unique under the Lee 356-120-TC out of my 9mm AR upper. Velocity across the chrony apprx. 1400 fps and shoots 2"-3" at 50 yards using the open sights. Plenty good enough to...
Forum: Group Buy Archives
Please put me on the list for one of these 4 cavity moulds.
catlynu-at-earthlink-dot-net
Thanks
SAJTU
+1 on Zomby's load. I've had great results in 03A3 and Garand using 311291 with 32 grains Varget and 311299 using 34 grains Varget, both with dacron filler. Both run mid 1900 fps over the chrony. ...
Forum: Military Rifles
03A3 stocks seem to go for $75 to $100. Really depends if it's a straight, scant, of C stock and condition. I'm needing one to put back an old sporter to original condition. I would be interested...
I've had good luck with 311291 (water dropped) and 20.0 grains of 2400 with a dacron filler out of my 2-groove 03A3. As suggested by Larry, it seems to be more accurate with the filler.
...
Link
I have a very similar 9mm AR and didn't get mine anywhere near 1500 fps. I've had good luck with Lee 356-120-TC and 5.7 grains of Unique with chrony'd velocity at 1400 fps. Got decent...
Forum: Casting Equipment
I picked up an open coil design at Big Lots for around $8.00. They also had some two element hot plates for not much more.
SAJTU
Forum: Military Rifles
+1 for Tim Shufflin...he does awesome parkerizing and fast turnaround
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |